Stress ratio effect on tension-tension fatigue behavior of angle-ply GFRP laminates

À propos
Confidentialité
Mentions légales

Graph Chatbot

Publications associées (30)

Experimental quantification of 3D deformations in sensitive clay during stress-probing

Edward Carlo Giorgio Andò

Unique four-dimensional (4D) deformation data are collected during drained triaxial tests on intact specimens of a natural sensitive clay. This requires the development of a miniature triaxial cell for advanced stress path testing, specifically designed fo ...

ICE PUBLISHING2022

Scaling Description of Creep Flow in Amorphous Solids

Marko Popovic, Matthieu Wyart, Wencheng Ji, Thomas Willem Jan de Geus

Amorphous solids such as coffee foam, toothpaste, or mayonnaise display a transient creep flow when a stress E is suddenly imposed. The associated strain rate is commonly found to decay in time as gamma_ -t-nu, followed either by arrest or by a sudden flui ...

AMER PHYSICAL SOC2022

Discretization Uncertainties of Flow and Fatigue Damage Simulations of a Reversible Francis Pump-Turbine at Off-Design Operation in Turbine Mode

Philippe Alexandre Bontemps, Drazen Dujic, Daniel Biner

In the framework of the XFLEX HYDRO H2020 European Project, a 5 MW reversible Francis pump-turbine prototype, equipped with an industrial full size frequency converter, is investigated to demonstrate enhanced grid regulation capacities of variable speed hy ...

SPRINGER INTERNATIONAL PUBLISHING AG2022

Determination of Parameters Characteristic of Dynamic Weakening Mechanisms During Seismic Faulting in Cohesive Rocks

Marie Estelle Solange Violay, Chiara Cornelio, François Xavier Thibault Passelègue

While sliding at seismic slip-rates of ∼1 m/s, natural faults undergo an abrupt decrease of shear stress called dynamic weakening. Asperity-scale processes related to flash heating and weakening and, meso-scale (mm-cm) processes involving shear across the ...

AGU2022

The thermally activated deformation behaviour of single-crystalline microcast aluminium wires

Andreas Mortensen, Léa Deillon, Suzanne Godelieve Alphonsine Verheyden

A microcasting process is used to produce high aspect ratio ( > 30) monocrystalline pure aluminium wires with a diameter between 14 and 115 mu m. The role of thermal activation in the plastic deformation of these microwires is measured by means of (single) ...

PERGAMON-ELSEVIER SCIENCE LTD2022

Design of slender and squat reinforced concrete members with shear reinforcement

Aurelio Muttoni, Miguel Fernández Ruiz, Marko Pejatovic

As proposed in several design standards for structural concrete, including Eurocode 2 (EN:1992-1-1:2004) and fib's Model Code 2010, the shear design of slender members with shear reinforcement can be performed by means of consistent models based on suitabl ...

ERNST & SOHN2022

On the behavior of uniaxial static stress loaded micro-scale fused silica beams at room temperature

Yves Bellouard, Christos Edouardos Athanasiou, Saood Ibni Nazir

The question of whether static stress in fused silica relaxes at room temperature is still under debate. Here, we report experimental data investigating the behavior of fused silica at room temperature when subjected to static tensile stress up to 2 GPa st ...

2022

Fatigue of reinforced UHPFRC members and monitoring of fatigue action effects on bridges

Bartlomiej Wojciech Sawicki

The objective of this thesis is to develop knowledge and methods to prevent fatigue failure of bridges. The Fatigue Limit State is investigated from both the demand (S) and resistance (R) side. The S-part focuses on reduction of uncertainties through monit ...

EPFL2021

Role of mean stress on fatigue behavior of a 316L austenitic stainless steel in LWR and air environments

Philippe Spätig, Hans-Peter Seifert

Mean stress effects on fatigue life of a stainless steel in air and boiling water reactor (BWR) environments were evaluated by load-controlled tests. In stress-life, non-zero mean stresses increase life in low cycle fatigue regime in both environments and ...

ELSEVIER SCI LTD2021

The influence of the kinematics of rough surface engagement on the transfer of forces in cracked concrete

Miguel Fernández Ruiz

One of the most instrumental aspects governing the response of structural concrete at ultimate limit state refers to the possibility of developing smeared cracking patterns within a member (associated normally to the presence of sufficient reinforcement fo ...

2021

Page 2 sur 2