Publications associées à Basic creep and autogenous shrinkage of Limestone Calcined Clay Cement (LC3)

Decarbonization potential of steel fibre-reinforced limestone calcined clay cement concrete one-way slabs

This study deals with a comparison of the environmental performance of one-way slabs utilizing steel fibrereinforced limestone calcined clay cement (LC3) concrete with the control case of Ordinary Portland cement concrete. The experimental program constitu ...

Elsevier Sci Ltd2024

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Xhemsi Malja

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Contradict mechanism of long-term magnesium and sodium sulfate attacks of nano silica-modified cement mortars - Experimental and thermodynamic modeling

Qiao Wang

The mechanisms of external sulfate attack on cement mortars containing nano silica have been studied under full immersion conditions after 3 years. The sulfate degradation processes were compared between sodium sulfate and magnesium sulfate solutions with ...

Elsevier Sci Ltd2024

Additively manufactured steel reinforcement for small scale reinforced concrete modeling: Tensile and bond behavior

Christian Leinenbach, Rafal Wróbel

Small scale (1:30-1:40) Reinforced Concrete is useful for centrifuge testing. However, manufacturing the reinforcing cages by hand at this scale is practically difficult. This paper suggests that small scale reinforcement can be manufactured using a metal ...

Elsevier Sci Ltd2024

Insights from an extensive triaxial testing campaign on a shale for comparative site characterization of a deep geological repository

Lyesse Laloui, Alessio Ferrari, Eleonora Crisci

Several boreholes were drilled for site comparison of a deep geological repository (DGR) in Northern Switzerland. The main target of the exploration program was the >100m thick Opalinus Clay, the designated host rock encountered at approximately 450 to 100 ...

Elsevier2024

Experimental investigation of dowel action in reinforcing bars using refined measurements

Aurelio Muttoni, Marko Pejatovic

In typical reinforced concrete design, reinforcement is designed to carry axial forces, but it can also resist transversal forces by dowel action. This is usually neglected for simplicity's sake in the design phase, but it can be accounted for either expli ...

Ernst & Sohn2024

Contributions to rebar-to-concrete interaction and its structural implications for design and monitoring applications

Enrique Corres Sojo

Bond between reinforcing bars and concrete has been the focus of extensive research over the last century. This is well-justified as the functioning of reinforced concrete intimately depends on the interaction between rebar and concrete, as for example cra ...

EPFL2024

A novel fatigue life prediction methodology based on energy dissipation in viscoelastic materials, synergistic effects of stress level, stress ratio, and temperature

Thomas Keller, Abdolvahid Movahedirad, Lulu Liu

This work introduces a new methodology to predict the fatigue life of viscoelastic materials by considering the creep effect on fatigue behavior under the concurrent effects of stress level, stress ratio, and temperature. The model established based on the ...

2024

Influence of Low- to Medium-Kaolinite Clay on the Durability of Limestone Calcined Clay Cement (LC3) Concrete

Karen Scrivener, Matea Flegar

The kaolinite content is principally responsible for the durability performance of Limestone Calcined Clay Cement (LC3), which calls into question its global applicability. The clay supply has a significant impact on the LC3 system's reduced carbon footpri ...

MDPI2023

Going Below 50% Clinker Factor in Limestone Calcined Clay Cements (LC3): A Comparison with Pozzolanic Cements from the South American Market

Karen Scrivener, Franco Alberto Zunino Sommariva

Limestone calcined clays are a promising technology as they offer similar performance to OPC from 7 days onwards, while enabling a reduction of the clinker content of 50%. In some regions of the world like South America, pozzolanic cements (i.e., blended c ...

SPRINGER INTERNATIONAL PUBLISHING AG2023

Does carbon footprint reduction impair mechanical properties and service life of concrete?

Karen Scrivener, Diana Londoño Zuluaga

The aim of this study is to evaluate how much the changes in the concrete mix design, which enable carbon footprint reduction, are impacting mechanical properties and predicted service life of concrete structure. The starting point of this study was concre ...

SPRINGER2023

Durability Challenges of Low-Grade Calcined Clay Opposed to High-Volume Fly Ash in General Purpose Concrete

Karen Scrivener, Matea Flegar

With the decrease in availability of common supplementary cementitious materials (SCMs) such as fly ash in Europe, the search for appropriate SCMs should be dealt with locally. A com-bination of abundant low-grade calcined clay and limestone powder has pro ...

AMER SOC TESTING MATERIALS2023

Characterisation and hydration kinetics of beta-C2S synthesised with K2SO4 as dopant

Karen Scrivener, Shashank Bishnoi, Franco Alberto Zunino Sommariva, Sreejith Krishnan

In this study, a protocol for synthesising beta-C2S using K2SO4 as a dopant has been reported. Quantitative X-Ray diffraction was used to characterise synthesised samples. It was observed that it is possible to synthesise beta-C2S with high purity (>96 wt% ...

Pergamon-Elsevier Science Ltd2023

Atomistic modeling of C-S-H: bulk and surface

Ziga Casar

By replacing part of Portland cement with so-called supplementary cementitious materials (SCMs) it is possible to reduce the CO2 footprint of the cement industry. These SCMs are commonly limestone, calcined clay, slag and fly ash. While doing so the early ...

EPFL2023

Data-driven optimization tool for the functional, economic, and environmental properties of blended cement concrete using supplementary cementitious materials

Hisham Tarek Mohamed Hafez

The need to produce more sustainable concrete is proving imminent given the rising environmental concerns facing the industry. Blended cement concrete, based on any of the prominent supplementary cementitious materials (SCMs) such as fly ash, ground granul ...

ELSEVIER2023

Unidirectional penetration approach for characterizing sulfate attack mechanisms on cement mortars and pastes

Karen Scrivener, Qiao Wang, William Wilson

Degradation of cementitious materials by sulfate ions is commonly classified into chemical and physical sulfate attack. So-called "physical" attack dominates in many field situations, but laboratory testing focuses on "chemical" attack under full-immersion ...

Pergamon-Elsevier Science Ltd2023

Bringing casting to microfabrication: processing and deformation of microcastings

Luciano Borasi

This work extends the range of pathways for the production of metallic microcomponents by downscaling metal casting. This is accomplished by using either of two different molding techniques, namely femtosecond laser micromachining or lithographic silicon m ...

EPFL2023

The role of Zn in C-S-H atomic structure, nucleation and growth

Anna Morales Melgares

The most promising solution towards cementitious materials with a lower carbon footprint is the partial substitution of the clinker by supplementary cementitious materials (SCMs) such as fly ash, blast furnace slag, limestone and calcined clays. The produc ...

EPFL2023

Elastic limit tensile stress of UHPFRC: Method of determination and effect of fiber orientation

Eugen Brühwiler, Emmanuel Denarié, Jian Zhan

This paper discusses the influence of fiber orientation on elastic limit tensile stress of ultra-high performance fiber reinforced cementitious composites (UHPFRC). An original model relating elastic limit tensile stress to fiber orientation is proposed, a ...

2023

The influence of lattice misfit on screw and edge dislocation-controlled solid solution strengthening in Mo-Ti alloys

William Curtin, Carolina Baruffi, You Rao

Mo-Ti alloys form solid solutions over a wide range of compositions, with lattice misfit parameters increasing significantly with titanium content. This indicates a strong increase in the critical stress for edge dislocation motion. Here, we probe the tran ...

SPRINGERNATURE2023