Recherche

Afficher tous les résultats pour

Accueil

Publication

Micro-addition of Fe in highly alloyed Cu-Ti alloys to improve both formability and strength

À propos
Confidentialité
Mentions légales

Graph Chatbot

Publications associées (34)

Page 2 sur 2

Liquid metal infiltration of silicon based alloys into porous carbonaceous materials Part-III: Experimental verification of conversion products and infiltration depth by infiltration of Si-Zr alloy into mixed SiC/ graphite preforms

Ludger Weber, Caroline Hain, Manoj Kondibhau Naikade, Annapaola Parrilli

Porous carbonaceous preforms, made from graphite and silicon carbide (SiC) powders, with varying graphite powder mass fractions and particle sizes, were infiltrated at 1500 degrees C and 1700 degrees C by Si-8 at. pct Zr alloy to produce dense Si-Zr-SiC co ...

ELSEVIER SCI LTD2023

The influence of lattice misfit on screw and edge dislocation-controlled solid solution strengthening in Mo-Ti alloys

William Curtin, Carolina Baruffi, You Rao

Mo-Ti alloys form solid solutions over a wide range of compositions, with lattice misfit parameters increasing significantly with titanium content. This indicates a strong increase in the critical stress for edge dislocation motion. Here, we probe the tran ...

SPRINGERNATURE2023

Equivalent Frame Models for FRP-Strengthened Masonry Buildings

Fibre-reinforced polymers (FRP) strengthening can be applied to decrease the seismic vulnerability of existing masonry buildings, both with regard to in-plane and out-of-plane failure mechanisms. Experimentally, the impact of strengthening solutions has be ...

Proceedings of the 2nd Croatian Conference on Earthquake Eng2023

Wear behaviour of novel copper alloy as an alternative to copper-beryllium

Roland Logé, Stefano Mischler, Anna Neus Igual Muñoz, Baptiste Thomas Jean Rouxel

Copper beryllium age hardenable alloys (Cu-Be) are widely used and appreciated for combining exceptional mechanical and electrical properties. However, the toxicity of these alloys pushes the scientific community to develop alternative alloys. Cu-Ni-Sn all ...

ELSEVIER SCIENCE SA2023

Process development of pre-impregnated hybrid thin-ply composites

Alexios Argyropoulos

Thin-ply composites, obtained with recently developed fiber spreading techniques, rapidly gained industrial interest because they offer a large composite design freedom, and lead to a composite tensile strength that is close to that of the individual fiber ...

EPFL2023

Micromechanics of oxide inclusions in ferrous alloys

Alejandra Inés Slagter

Oxide inclusions are inevitably present in steel as a direct consequence of the steelmaking process; as a result, a cubic centimetre of modern steel will generally contain about a million of these hard and brittle micrometre-sized ceramic particles. Inclus ...

EPFL2023

Energy dissipation in fiber-polymer composites adhesive joints under cyclic loading

Ghazaleh Eslami

Sustainable development has emerged as a paramount consideration in various fields of industry, including construction, to preserve the environment and its finite resources. Lightweight structures, such as fiber-polymer composite structures, address both s ...

EPFL2023

Simple shear extrusion versus equal channel angular pressing: A comparative study on the microstructure and mechanical properties of an Mg alloy

Roland Logé, Cyril Cayron, Aryan Rezaei Rad

Two severe plastic deformation (SPD) techniques of simple shear extrusion (SSE) and equal channel angular pressing (ECAP) were employed to process an extruded Mg -6Gd -3Y -1.5Ag (wt%) alloy at 553 K for 1, 2, 4 and 6 passes. The microstructural evolutions ...

KEAI PUBLISHING LTD2023

The General Crack Component Model for reversed cyclic shear

David Michael Volpe Ruggiero

A growing body of research has shown that reversed cyclic shear loading of reinforced concrete (RC) causes effects that are not accounted for in monotonic behavioral models. Notable among these effects are a reduction in shear strength and significant plas ...

2023

Origin of the enhanced pseudo-elasticity of additively manufactured Fe-17Mn-5Si-4Ni-10Cr-(V, C) shape memory alloy fabricated by laser powder bed fusion

Christian Leinenbach, Irene Ferretto

This study investigated the origin of the enhanced pseudo-elasticity of additively manufactured vanadium carbide-containing Fe-based shape memory alloys. The aged samples with two different starting microstructures, as-built and solution-treated, showed co ...

Elsevier Science Sa2023

Simultaneous strength and ductility enhancement of wire-arc directed energy deposited Al-Cu alloy by interlayer laser shock peening

Ke Huang, Yandong Jing

Wire-arc directed energy deposition (wire-arc DED), recognized for its ability to produce large-scale parts, has gained considerable attention. However, a critical issue with this method is the high prevalence of internal porosity defects found in the manu ...

Elsevier Science Sa2023

Crystalline or amorphous? A critical evaluation of phenomenological phase selection rules

Johann Michler, Caroline Hain

In this work, we reviewed the available phase selection rules comprising atomic size and topological aspects, entropies, enthalpies, melting points, valence and itinerant electron concentrations, as well as electronegativity, and validated them using a car ...

ELSEVIER SCI LTD2023

Role of Minimum Adhesive Wear Particle Size in Third-Body Layer Properties

Jean-François Molinari, Son-Jonathan Pham-Ba

We employ a novel discrete element method (DEM) force formulation to simulate adhesive wear and assess the effects of material and loading parameters on the properties of the third-body layer (TBL) formed during sliding motion. The study emphasizes the rol ...

2023

Imaging Radial Distribution Functions of Complex Particles by Relayed Dynamic Nuclear Polarization

David Lyndon Emsley, Arthur César Pinon, Pierrick Berruyer

The physical properties of many modern multi-component materials are determined by their internal microstructure. Tools capable of characterizing complex nanoscale architectures in composite materials are, therefore, essential to design materials with targ ...

2023