Mediaspace scheduled maintenance: Aug 25, 2026 07:00 - 12:00 AM. During this time, videos will be temporarily unavailable. Check status updates.

Concept

Failure mode and effects analysis

Publications associées (32)

Manufacturing and toughening effects on the material properties of wind turbine blade adhesives

Anastasios Vassilopoulos, Dharun Vadugappatty Srinivasan

Hybrid adhesives can be developed using commercially available adhesive materials and customized to the required loading conditions. In this paper, SPABONDTM 820HTA (non-toughened) and SPABONDTM 840HTA (toughened) adhesives are hybridized by two strategies ...

2022

Review of degradation and failure phenomena in photovoltaic modules

Sameh Ahmad Kantoush

The degradation of photovoltaic (PV) systems is one of the key factors to address in order to reduce the cost of the electricity produced by increasing the operational lifetime of PV systems. To reduce the degradation, it is imperative to know the degradat ...

PERGAMON-ELSEVIER SCIENCE LTD2022

Anchorage of shear reinforcement in beams and slabs

Aurelio Muttoni, Miguel Fernández Ruiz, Qianhui Yu, Frédéric Monney

Anchorage of shear reinforcement, such as links or stirrups, can be performed by providing hooks, bends or heads at their ends, by welding transverse reinforcement or by closing open stirrups with pins. Hooks and bends, also used to enhance the anchorage o ...

2022

Assessment of stiffener spacing design requirements for intermediate EBF links via nonlinear finite element analysis

Dimitrios Lignos, Nikolaos Skretas

Links in eccentrically braced frames (EBFs) with intermediate length are designed with transverse web stiffeners. Web stiffening is required because the common failure modes are associated with web buckling as well as flange and lateral torsional buckling. ...

ETAM2022

Corrosion testing of solar cells: Wear-out degradation behavior

Christophe Ballif, Alessandro Francesco Aldo Virtuani, Andrew Wayne Fairbrother, Luca Gnocchi

Corrosion is one of the main end-of-life degradation and failure modes in photovoltaic (PV) modules. However, it is a gradual process and can take many years to become a major risk factor because of the slow accumulation of water and acetic acid (from enca ...

ELSEVIER2022

Failure mechanism of fine-grained soil-structure interface for energy piles

Lyesse Laloui, Elena Ravera

The response of the soil-structure interface can significantly affect the performance of any geotechnical structure. Thermal cycles are a new factor that influence the response to all structures that have an energy function in addition to the structural on ...

2022

Shear Response of Wet Weak Carbonate Rock/Grout Interfaces Under Cyclic Loading

Eleni Stavropoulou

The development and construction of offshore wind farms requires the correct estimation of the friction that can be mobilised at the rock/grout interface. In conventional studies, the shear behaviour of a joint is usually investigated with laboratory tests ...

2021

Casting position effects on bond performance of reinforcement bars

Aurelio Muttoni, Miguel Fernández Ruiz, Francesco Rafael Alberto Moccia

The phenomena associated with the consolidation of fresh concrete (bleeding and plastic settlement) are commonly considered significant for the bond performance of reinforcement. However, rules to take care of such influence for design are not consistent a ...

ERNST & SOHN2021

Risk-based methodology to assess bridge condition based on visual inspection

Eugen Brühwiler, Numa Joy Bertola

The visual inspection of existing infrastructure is a critical step for asset management, as the detection and quantification of damage must be useful to prioritise maintenance. In Switzerland, main inspections are made every five years for all road bridge ...

2021

Uncertainties in the Seismic Assessment of Historical Masonry Buildings

Katrin Beyer, Igor Tomic, Francesco Vanin

Seismic assessments of historical masonry buildings are affected by several sources of epistemic uncertainty. These are mainly the material and the modelling parameters and the displacement capacity of the elements. Additional sources of uncertainty lie in ...

2021

Automated test setup to quantify the lifetime of dielectric elastomer actuators under a wide range of operating conditions

Herbert Shea, Fabio Beco Albuquerque, Djen Timo Kühnel, Valentin Colin Py

We present an automated test setup for the systematic performance and lifetime evaluation of dielectric elastomer actuators (DEAs). This setup, called the MAPLE setup, performs accelerated aging tests and allows quantifying how material choice, fabrication ...

IOP PUBLISHING LTD2021

Origami-inspired carbon fiber-reinforced composite sandwich materials - Fabrication and mechanical behavior

Thomas Keller

A folding fabrication method inspired by origami for carbon fiber-reinforced composites to fabricate three-dimensional structures is presented. PMI foams serve as substrates, making it possible to manufacture this kind of origami-inspired composite sandwic ...

ELSEVIER SCI LTD2021