Publications associées à Essai de traction

Publications associées (28)

Edible Soft Actuators based on Konjac Glucomannan for Underwater Operation

Dario Floreano, Jun Shintake, Bokeon Kwak, Markéta Pankhurst, Ryo Kanno

Soft robots are being increasingly developed and deployed for underwater applications such as exploration, monitoring, and rescue owing to their innate compliance, mechanical and chemical stability, and waterproof properties. However, they are still predom ...

2024

Influence of fiber orientation on the tensile behavior of UHPFRC and reinforced UHPFRC under static and fatigue loadings

Jian Zhan

Ultra-high performance fiber reinforced cementitious composite (UHPFRC) is a modern class of cementitious building materials. Because of its superior mechanical properties and durability, it is increasingly used globally to rehabilitate, strengthen and mod ...

EPFL2024

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Landolf-Giosef-Anastasios Rhode-Barbarigos, Tara Habibi

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

2024

Experimental investigation of dowel action in reinforcing bars using refined measurements

Aurelio Muttoni, Marko Pejatovic

In typical reinforced concrete design, reinforcement is designed to carry axial forces, but it can also resist transversal forces by dowel action. This is usually neglected for simplicity's sake in the design phase, but it can be accounted for either expli ...

Ernst & Sohn2024

A novel fatigue life prediction methodology based on energy dissipation in viscoelastic materials, synergistic effects of stress level, stress ratio, and temperature

Thomas Keller, Lulu Liu, Abdolvahid Movahedirad

This work introduces a new methodology to predict the fatigue life of viscoelastic materials by considering the creep effect on fatigue behavior under the concurrent effects of stress level, stress ratio, and temperature. The model established based on the ...

2024

Influence of Fiber Orientation on the Elastic Limit Tensile Stress of UHPFRC

Eugen Brühwiler, Emmanuel Denarié, Jian Zhan

The elastic limit tensile stress of UHPFRC is governed by contributions of the cementitious matrix and the fibrous skeleton. This paper finds that fiber orientation has significant influence on the matrix tensile strength of UHPFRC, while this is not consi ...

2023

Deformation response of highly stretchable and ductile graphene kirigami under uniaxial and biaxial tension

Ye Wei, Yao Chen

Kirigami, the ancient technique of paper cutting, has been successfully applied to enhance the stretchability and ductility of nanoscale graphene. However, existing experimentally realized graphene kirigami (GK) are created by introducing parallel cuts, ex ...

Amer Physical Soc2023

Bringing casting to microfabrication: processing and deformation of microcastings

Luciano Borasi

This work extends the range of pathways for the production of metallic microcomponents by downscaling metal casting. This is accomplished by using either of two different molding techniques, namely femtosecond laser micromachining or lithographic silicon m ...

EPFL2023

Multi-scale characterization and modeling of notched strength and translaminar fracture in hybrid thin-ply composites based on different carbon fiber grades

Guillaume Clément Broggi

Owing to their high specific stiffness and strength, Carbon Fiber Reinforced Composites (CFRP) are ideal candidates for the development of lightweight high-performance structures. Within this family, thin-ply composites allow for wider design freedom and p ...

EPFL2023

Scanning Small-Angle X-ray Scattering of Injection-Molded Polymers: Anisotropic Structure and Mechanical Properties of Low-Density Polyethylene

Marianne Liebi, Manuel Guizar Sicairos

Injection molding is known to create a layered anisotropicmorphologyacross the sample thickness due to varying shear and cooling ratesduring the manufacturing process. In this study, scanning small-angleX-ray scattering was used to visualize and quantify t ...

AMER CHEMICAL SOC2023

Incorporation of Lignin in Bio-Based Resins for Potential Application in Fiber-Polymer Composites

Mateus De Assunção Hofmann

Bio-based resins, obtained from renewable raw materials, are a more sustainable alternative to oil-based resins for fiber-reinforced polymer (FRP) composites. The incorporation of lignin in those resins has the potential to enhance their performance. This ...

MDPI2023

Elastic limit tensile stress of UHPFRC: Method of determination and effect of fiber orientation

Eugen Brühwiler, Emmanuel Denarié, Jian Zhan

This paper discusses the influence of fiber orientation on elastic limit tensile stress of ultra-high performance fiber reinforced cementitious composites (UHPFRC). An original model relating elastic limit tensile stress to fiber orientation is proposed, a ...

2023

Quantitative study of the thickness-dependent stress in indium tin oxide thin films

Blaise François Cuénod, Rémy David Désiré Juttin

A quantitative analysis of stress in indium tin oxide (ITO) films with varying thicknesses was conducted using high-precision stylus profilometry. The experimental results revealed a transition of the stress type from tensile to compressive as the ITO film ...

Elsevier Science Sa2023

Simultaneous strength and ductility enhancement of wire-arc directed energy deposited Al-Cu alloy by interlayer laser shock peening

Ke Huang, Yandong Jing

Wire-arc directed energy deposition (wire-arc DED), recognized for its ability to produce large-scale parts, has gained considerable attention. However, a critical issue with this method is the high prevalence of internal porosity defects found in the manu ...

Elsevier Science Sa2023

Three-dimensional hydraulic fracture propagation in homogeneous and heterogeneous media

Carlo Peruzzo

Hydraulic fractures are tensile fractures that occur in solid materials due to the natural intrusion or anthropogenic injection of a viscous fluid into a fracture channel. The deliberate creation of hydraulic fractures is part of an industrial technology h ...

EPFL2023

Propagation of planar three-dimensional buoyant hydraulic fractures

Andreas Möri

Hydraulic fractures are driven by an internal fluid pressure exceeding the minimum compressive stress, propagating in a direction perpendicular to the latter. This class of tensile fractures has gained interest over the last fifty years due to the developm ...

EPFL2023

INFLUENCE OF VOIDS ON THICK DCB JOINT BEHAVIOR

Véronique Michaud, Anastasios Vassilopoulos, Jialiang Fan

The influence of voids on the quasi-static Mode I fracture performance of thick adhesive joints was investigated in this article. Double Cantilever Beam (DCB) joints were manufactured with glass fiber reinforced epoxy adherends and SikaPower®-830 epoxy adh ...

2023

The influence of lattice misfit on screw and edge dislocation-controlled solid solution strengthening in Mo-Ti alloys

William Curtin, Carolina Baruffi, You Rao

Mo-Ti alloys form solid solutions over a wide range of compositions, with lattice misfit parameters increasing significantly with titanium content. This indicates a strong increase in the critical stress for edge dislocation motion. Here, we probe the tran ...

SPRINGERNATURE2023

Process development of pre-impregnated hybrid thin-ply composites

Alexios Argyropoulos

Thin-ply composites, obtained with recently developed fiber spreading techniques, rapidly gained industrial interest because they offer a large composite design freedom, and lead to a composite tensile strength that is close to that of the individual fiber ...

EPFL2023

Reinforced Supramolecular Networks of End Functionalized Polymers for Tailored Thermomechanical Property Profiles

Yevhen Hryshunin

Thermoset rubbers give rise to elastomers with tunable stiffness and high resilience but are not recyclable. Thermoplastic elastomers can address this problem but their broad applicability is impeded by either limited operating temperatures or inferior ela ...

EPFL2023