Mediaspace scheduled maintenance: Aug 25, 2026 07:00 - 12:00 AM. During this time, videos will be temporarily unavailable. Check status updates.

Concept

Corrosion engineering

Publications associées (32)

Tribocorrosion of a CoCrMo alloy in sulfuric acid - Glycerol mixtures

Stefano Mischler, Shoufan Cao

This work reports on the tribocorrosion properties of a CoCrMo alloy sliding under imposed passive potential against alumina in sulfuric acid-glycerol mixtures exhibiting different viscosities and thus, in principle, lubrication properties. As expected, we ...

ELSEVIER SCIENCE SA2020

Understanding the carbonation of concrete with supplementary cementitious materials: a critical review by RILEM TC 281-CCC

Karen Scrivener

Blended cements, where Portland cement clinker is partially replaced by supplementary cementitious materials (SCMs), provide the most feasible route for reducing carbon dioxide emissions associated with concrete production. However, lowering the clinker co ...

SPRINGER2020

Corrosion Mechanisms of Diamond-like Carbon Coated Interlayers & Interfaces

Emilija Ilic

Diamond-like carbon (DLC) coatings can improve the wear resistance of articulating implants. However despite successful in-vitro testing, some DLC coated joint replacements had to be revised prematurely, mainly due to coating delamination induced by corros ...

EPFL2019

Data Science Based Mg Corrosion Engineering

Félix Benedito Clément Musil, Robert Horst Meissner

Magnesium exhibits a high potential for a variety of applications in areas such as transport, energy and medicine. However, untreated magnesium alloys are prone to corrosion, restricting their practical application. Therefore, it is necessary to develop ne ...

2019

'Green' Cr(iii)-glycine electrolyte for the production of FeCrNi coatings: electrodeposition mechanisms and role of by-products in terms of coating composition and microstructure

Stefano Mischler, Johann Michler, Enrico Bertero

The electrodeposition of stainless steel-like FeCrNi alloys for miniaturised devices is appealing as it would allow combining excellent material properties (e.g. corrosion resistance, hardness, biocompatibility) at low-cost. However, conventional baths oft ...

2019

Tribological response of multilayered gold nickel coating deposited on fine turned surfaces

Stefano Mischler, Valentine Agnès Madeleine Magnin

Gold coating are widely used in industry due to their corrosion resistance, electrical conductivity and low contact resistance. However, friction and wear can limit their functionality and lifetime. This study addresses the degradation of a commercial fine ...

ELSEVIER SCIENCE SA2019

The corrosion rate and microstructure of Portland cement and calcium aluminate cement-based concrete mixtures in outfall sewers: A comparative study

Karen Scrivener

This paper presents a comparative study on the corrosion rate and microstructural characteristics of Portland cement (PC) and calcium aluminate cement (CAC)-based concrete mixtures subjected to microbially-induced sulphuric acid (biogenic H2SO4) attack for ...

Pergamon-Elsevier Science Ltd2019

Silicon Corrosion in Neutral Media: The Influence of Confined Geometries and Crevice Corrosion in Simulated Physiological Solutions

Stefano Mischler, Emilija Ilic

Silicon (Si) based implantable components are widely used to restore functionalities in the human body. However, there have been reported instances of Si corroding after only a few years of implantation. A key parameter often overlooked when assessing Si s ...

2019

On-Site Purification of Copper-Contaminated Vanadium Electrolytes by using a Vanadium Redox Flow Battery

Hubert Girault, Heron Vrubel, Danick Reynard, Christopher Raymond Dennison, Alberto Battistel

Corrosion of carbon-based electrodes and bipolar plates is a major hurdle and can be a cause of failure in commercial vanadium redox flow batteries (VRFBs). Carbon corrosion was found to occur in a commercial VRFB (10 kW/40 kWh), whereby cracks through bip ...

WILEY-V C H VERLAG GMBH2019

Corrosion behaviour of Ti6A14V ELI nanotubes for biomedical applications

Anna Neus Igual Muñoz

Surfaces engineering on titanium biomedical alloys aiming for improving bone regeneration, healing periods and increasing lifetime needs fora fundamental understanding of the electrochemical reactions occurring at the interface biomaterial/human fluid. The ...

2019

Analysis of High Temperature Degradation of Alloys in Solid Oxide Fuel Cell

Manuel Bianco

Solid oxide fuel cells (SOFCs) are approaching commercialization to improve power production efficiency. Currently, cost and lifetime reliability limit their spread in the market. The SOFC is ceramic-based, but refractory metal alloys are in fact the major ...

EPFL2019

Application of Time Series Methods on Long-Term Structural Monitoring Data for Fatigue Analysis

Eugen Brühwiler, Bartlomiej Wojciech Sawicki

Structural health monitoring (SHM) can be employed to reduce uncertainties in different aspects of structural analysis such as: load modeling, crack development, corrosion rates, etc. Fatigue is one of the main degradation processes of structures that caus ...

2019