Mediaspace scheduled maintenance: Aug 25, 2026 07:00 - 12:00 AM. During this time, videos will be temporarily unavailable. Check status updates.

Concept

Forensic materials engineering

Publications associées (10)

Advanced analytical electron microscopy applied to Solid Oxide Cell materials and their degradation

Stéphane François Jean Poitel

Electron microscopy offers a wide range of techniques to study materials. Environmental Scanning Electron Microscopy (ESEM), in particular, allows the characterisation of samples at high-temperature using a laser heating stage, and under various gaseous at ...

EPFL2020

Improved mechanical dispersion or use of coupling agents? Advantages and disadvantages for the properties of fluoropolymer/ceramic composites

Jan-Anders Edvin Maansson, Véronique Michaud, Yves Leterrier, Dragan Damjanovic, Sara Dalle Vacche

The aim of this work is to investigate the influence of interfacial chemistry on the properties of fluoropolymer composites, independent of effects derived from changes in morphology, in particular particle dispersion state. A comparative study of solvent ...

2018

Very high cycle fatigue tests with quenched and self-tempered reinforcement steel bars

Eugen Brühwiler, Alain Nussbaumer, Marina Rocha Pinto Portela Nunes

Investigations on the fatigue strength of steel reinforcement bars (rebars) mainly involves fatigue tests with hot rolled (HR) and cold worked (CW) steels. However, in the last few decades, HR and CW rebars were replaced by quenched and selftempered (QST) ...

Springer Verlag2016

Failure of mounting bolt of helicopter main gearbox support strut

Predrag Andric

The mounting bolt of helicopter main gearbox support strut was fractured into two pieces during the flight mission. The fracture occurred at the root of the first engaged thread of the bolt-nut assembly. Visual inspection of the fracture zone revealed crac ...

Elsevier2016

Effect of interfacial interactions on the electromechanical response of poly(vinylidene fluoride-trifluoroethylene)/BaTiO3 composites and its time dependence after poling

Jan-Anders Edvin Maansson, Véronique Michaud, Yves Leterrier, Dragan Damjanovic, Sara Dalle Vacche

Solvent cast and compression molded composite films based on poly(vinylidene fluoride-trifluoroethylene), containing pristine and silylated BaTiO3 particles, were poled, and their electromechanical response (d(33)), their dielectric properties, and the cry ...

Elsevier2015

Surface 3D Micro Free Forms: Multifunctional Microstructured Mesoporous alpha-Alumina by in Situ Slip Casting Using Excimer Laser Ablated Polycarbonate Molds

Patrik Willi Hoffmann, Paul Bowen, Sriharitha Rowthu

Ceramic surface microstructuring is a rapidly growing field with a variety of applications in tribology, wetting, biology, and so on. However, there are limitations to large-area microstructuring and fabrication of three-dimensional (3D) micro free forms. ...

Amer Chemical Soc2015

Edge strength model for glass based on the mirror zone depth

Pieter Christian Louter

A reliable assessment of the edge strength becomes an important issue when designing structural glass elements in buildings. However, in the literature the edge strength of glass, dependent on the edge quality, is not well documented. Therefore, in this st ...

2014

The effect of processing conditions on the morphology, thermomechanical, dielectric, and piezoelectric properties of P(VDF-TrFE)/BaTiO3 composites

Jan-Anders Edvin Maansson, Véronique Michaud, Yves Leterrier, Dragan Damjanovic, Sara Dalle Vacche, Fabiane Costa Oliveira Moffat

In this study (0-3) P(VDF-TrFE)/BaTiO3 composites containing up to 60 vol% of ceramic phase were prepared by solvent casting or compression molding. Their thermomechanical, dielectric, and piezoelectric properties were investigated, and discussed in the li ...

Springer Verlag2012

Mechanics of Growth and Coalescence of Pre-existing Voids in a Ductile Matrix

Tomasz Jodlowski

This research project experimentally and numerically investigates the growth and coalescence of pre-existing voids for a wide range of stress states in a ductile matrix with a special focus on shear dominated loading conditions and presents quantitative ki ...

EPFL2011

The constitutive response of brazing alloys and the residual stresses in ceramic-metal joints

Matteo Galli

Nowadays the joining of dissimilar materials is often the only solution to fulfill the complex requirements of high technology applications. One of the fields in which the research activity is more intense and promising is that of the brazing of ceramics w ...

EPFL2007