Publications related to Bond behaviour of straight, hooked, U-shaped and headed bars in cracked concrete

Related publications (30)

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Experimental investigation of dowel action in reinforcing bars using refined measurements

Aurelio Muttoni, Marko Pejatovic

In typical reinforced concrete design, reinforcement is designed to carry axial forces, but it can also resist transversal forces by dowel action. This is usually neglected for simplicity's sake in the design phase, but it can be accounted for either expli ...

Ernst & Sohn2024

Contributions to rebar-to-concrete interaction and its structural implications for design and monitoring applications

Enrique Corres Sojo

Bond between reinforcing bars and concrete has been the focus of extensive research over the last century. This is well-justified as the functioning of reinforced concrete intimately depends on the interaction between rebar and concrete, as for example cra ...

EPFL2024

Experimental and analytical investigation of shear-reinforced concrete and dowel action

Marko Pejatovic

Codes of practice can be overly conservative, particularly for the shear resistance of reinforced concrete beams with shear reinforcement when large loads act close to supports. This thesis addresses the topic by proposing a refined design approach based o ...

EPFL2024

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Landolf-Giosef-Anastasios Rhode-Barbarigos, Tara Habibi

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

2024

Estimation of the bar stress based on crack width measurements in reinforced concrete structures

Aurelio Muttoni, Enrique Corres Sojo

Estimating the stress of reinforcing bars and its variations in service conditions can be useful to determine the reserve capacity of structures or to assess the risk of fatigue in the reinforcement. This paper investigates the use crack width measurements ...

Ernst & Sohn2024

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Diego Hernández Fraile

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

EPFL2024

Influence of fiber orientation on the tensile behavior of UHPFRC and reinforced UHPFRC under static and fatigue loadings

Jian Zhan

Ultra-high performance fiber reinforced cementitious composite (UHPFRC) is a modern class of cementitious building materials. Because of its superior mechanical properties and durability, it is increasingly used globally to rehabilitate, strengthen and mod ...

EPFL2024

FLO:RE – A new floor system made of reused reinforced concrete and steel elements

Corentin Jean Dominique Fivet, Numa Joy Bertola, Maléna Bastien Masse, Célia Marine Küpfer

Carefully extracting reinforced concrete (RC) elements from soon-to-be demolished structures and reusing them as load-bearing components is an emerging circular low-carbon alternative to building new structures. As floor construction typically accounts for ...

IABSE2024

Mesh-based topology, shape and sizing optimization of ribbed plates

Ahmad Abdulrahman Ahmad Majdouba

In this paper, we present a new parameterization and optimization procedure for minimizing the weight of ribbed plates. The primary goal is to reduce embodied CO2 in concrete floors as part of the effort to diminish the carbon footprint of the construction ...

Springer2024

Additively manufactured steel reinforcement for small scale reinforced concrete modeling: Tensile and bond behavior

Christian Leinenbach

Small scale (1:30-1:40) Reinforced Concrete is useful for centrifuge testing. However, manufacturing the reinforcing cages by hand at this scale is practically difficult. This paper suggests that small scale reinforcement can be manufactured using a metal ...

Elsevier Sci Ltd2024

Reusability assessment of reinforced concrete components prior to deconstruction from obsolete buildings

Corentin Jean Dominique Fivet, Maléna Bastien Masse, Julie Rachel Devènes

A large part of building demolitions is motivated by purely socio-economic reasons. Hence, about-to-be-demolished structures, commonly made of reinforced concrete, very often present no or little degradation. When adaptive reuse of the entire building is n ...

2024

Decarbonization potential of steel fibre-reinforced limestone calcined clay cement concrete one-way slabs

Hisham Tarek Mohamed Hafez, Beatrice Malchiodi

This study deals with a comparison of the environmental performance of one-way slabs utilizing steel fibrereinforced limestone calcined clay cement (LC3) concrete with the control case of Ordinary Portland cement concrete. The experimental program constitu ...

Elsevier Sci Ltd2024

Structural component reuse of precast and cast-in-place reinforced concrete in architecture since the late 1960s in Europe

Corentin Jean Dominique Fivet, Célia Marine Küpfer

The reuse of concrete pieces salvaged from structures undergoing transformation or demolition into new architectural projects has gained a sudden and visible interest over the past five years. However, the practice of reusing concrete pieces in new structu ...

vdf Hochschulverlag AG2024

Two-dimensional quasi-static delamination in composite laminates under Mode-I and Mode-II conditions

Congzhe Wang

Fiber-polymer composites consist of a polymer matrix and reinforcing fibers made of various materials. These composites exhibit exceptional properties, such as a high strength-to-weight ratio and excellent corrosion resistance, which has led to their incre ...

EPFL2024

A concrete answer for circular construction: three prototypes reusing saw-cut elements

Corentin Jean Dominique Fivet, Maléna Bastien Masse, Célia Marine Küpfer

Existing concrete buildings should be retained for as long as possible to reduce the environmental burden of demolition and new construction. However, when urban pressure makes demolition unavoidable, salvaging and reusing concrete elements elsewhere in ne ...

2024

Reuse of cut concrete slabs in new buildings for circular ultra-low-carbon floor designs

Corentin Jean Dominique Fivet, Numa Joy Bertola, Célia Marine Küpfer

The study explores an original idea that responds to the urgent need to reduce the detrimental environmental impacts of load-bearing floor construction in new buildings by reusing saw-cut reinforced concrete (RC) pieces salvaged from soon-to-be demolished ...

2024

Water weakening and the compressive brittle strength of carbonates: Influence of fracture toughness and static friction

Marie Estelle Solange Violay, Corentin Jean-Marie Rémi Noël, Barnaby Padraig Fryer

Water is ubiquitous within the pore space of rocks and has been shown to affect their physical and mechanical behaviour. Indeed, water can act on the rock strength via mechanical (i.e., reducing the effective stresses) or chemical effects (e.g., mineral di ...

2024

An adaptive phase field approach to 3D internal crack growth in rocks

Tao Xu, Michael Heap, Alexandra Roma Larisa Kushnir

Modeling the 3D internal crack under compression entails complex fracture mechanics (mode I-II-III fracture), resulting in substantial computational costs and challenges in characterizing fracture morphology characterization for Phase Field Method (PFM) si ...

2024

Numerical investigation of two-dimensional Mode-II delamination in composite laminates

Thomas Keller, Anastasios Vassilopoulos, Congzhe Wang

Existing standards for delamination tests on composite materials typically employ one-dimensional (1D) beam specimens. However, such specimens may not represent real delamination scenarios in composite structures, where cracks tend to propagate in two dime ...

Elsevier Sci Ltd2024