Durability of SG-laminated reinforced glass beams: effects of temperature, thermal cycling, humidity and load-duration

Chat with Graph Search

Ask any question about EPFL courses, lectures, exercises, research, news, etc. or try the example questions below.

DISCLAIMER: The Graph Chatbot is not programmed to provide explicit or categorical answers to your questions. Rather, it transforms your questions into API requests that are distributed across the various IT services officially administered by EPFL. Its purpose is solely to collect and recommend relevant references to content that you can explore to help you answer your questions.

Steel frame structures are essential components of modern infrastructure. Understanding their behavior under seismic loading is critical for ensuring public safety and minimizing damage that occurs during earthquakes. To accurately predict the response of ...

Carefully extracting reinforced concrete (RC) elements from soon-to-be demolished structures and reusing them as load-bearing components is an emerging circular low-carbon alternative to building new structures. As floor construction typically accounts for ...

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

Codes of practice can be overly conservative, particularly for the shear resistance of reinforced concrete beams with shear reinforcement when large loads act close to supports. This thesis addresses the topic by proposing a refined design approach based o ...

In the evolution of structural glass beam elements, the requirements for post-fracture load bearing capacity and safe failure behaviour have led to the development of reinforced and post-tensioned beams. Maximum bending capacity in the post-fracture state ...

This paper discusses the cyclic performance of a heavily instrumented 2-bay full-scale composite-steel moment resisting frame (CMRF) sub-system from the onset of structural damage up until incipient collapse. The CMRF featured stiffened end plate bolted co ...

Every engineering calculation is an approximation of reality, with inevitable uncertainties involved. This fact implies that a reliability verification accounting for the uncertainties is a necessary step in the design and assessment of structures. Nowaday ...

The seismic assessment of existing steel structures necessitates the development of practice- oriented engineering models for use in nonlinear static and dynamic analysis procedures. These models should encompass the full range of the anticipated nonlinear ...

With the advent of performance-based earthquake engineering (PBEE), the need for reliable prediction of earthquake-induced collapse of structures is essential. Despite the significant progress that has been made towards this goal, there are several hurdles ...

As proposed in several design standards for structural concrete, including Eurocode 2 (EN:1992-1-1:2004) and fib's Model Code 2010, the shear design of slender members with shear reinforcement can be performed by means of consistent models based on suitabl ...

Ultra high performance fiber reinforced cementitious composites (UHPFRCs) have demonstrated their outstanding efficiency as structural materials. Determination of the bending resistance of members combining UHPFRC with steel reinforcement bars (R-UHPFRC) u ...

This paper summarizes preliminary findings of nonlinear simulations aiming to quantify the seismic demands of codecompliant steel MRFs with variable panel zone targeted shear distortions, 𝛾!. The probability of beam fractures is explicitly considered in th ...

The increasing usage of nonlinear analyses for the design of reinforced concrete structures and the necessity of codes of practice to provide a consistent safety format for them is one of the challenges that new generations of codes of practice are facing. ...

The concept of post-tensioned glass beams builds on the concrete analogy of the reinforced glass beams. By additionally prestressing the reinforcement in a post-tensioned system, a compressive pre-stress is applied on the glass, enhancing the initial fract ...

Numerical models that can simulate coupled geometric instabilities in steel beam-columns are required for the seismic assessment of certain steel moment-resisting frames. Reliably simulating coupled instabilities requires that the steel material is precise ...

In steel moment resisting frames (MRFs) with composite floor slabs, seismic loads are transmitted from the slab into the beam through shear studs. Shear strength degradation of the studs due to cyclic loading results into the loss of the load transfer mech ...

Traditionally, the concrete strength is measured on cubes or cylinders having normalized dimensions, suitable vibration and curing conditions and their strength is assessed in laboratory under fast loading rates. However, the in-situ strength of structural ...

The effectiveness of post-tensioning in enhancing the fracture resistance of glass beams depends on the level of compressive pre-stress introduced at the glass edge surface that will in service be exposed to tensile stresses induced by bending. Maximum pre ...

Tensegrity structures have been widely utilized as lightweight structures due to their high stiffness-to-mass and strength-to-mass ratios. Minimal mass design of tensegrity structures subject to external loads and specific constraints (e.g., member yieldin ...

The behavior of reinforced-concrete structural elements under moving loads involves many complex parameters related to material properties, vehicle loading, environmental changes and structural response. It is difficult to generate the real conditions of l ...

Durability of SG-laminated reinforced glass beams: effects of temperature, thermal cycling, humidity and load-duration

Chat with Graph Search

A Softening Constitutive Law and Gradient-Inelastic Fiber-Based Element for 3-Dimensional Frame Simulations Under Seismic Excitations

FLO:RE – A new floor system made of reused reinforced concrete and steel elements

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Experimental and analytical investigation of shear-reinforced concrete and dowel action

Exploring the potential of the critical shear crack theory for reinforced and post-tensioned glass beams: Initial analysis and experiments

Full Scale Experiments of a Composite Steel Moment Resisting Frame: Behavioral Insights and Implications on Seismic Design

Reliability analysis and partial safety format calibration considering the characteristics of the resistance of reinforced concrete structures

The new Chapter 9 of Eurocode 8 Part 3 for Seismic Assessment of Existing Steel Structures

The Role of the Composite Floor System and Framing Action in the Seismic Performance of Composite Steel Moment-Resisting Frames

Design of slender and squat reinforced concrete members with shear reinforcement

Inverse Analysis of R-UHPFRC Beams to Determine the Flexural Response under Service Loading and at Ultimate Resistance

Seismic stability of steel moment resisting frames with inelastic panel zones

Considerations on the partial safety factor format for reinforced concrete structures accounting for multiple failure modes

Flexural behaviour of post-tensioned glass beams: Experimental and analytical study of three beam typologies

Reduced-order Models for Simulating Coupled Geometric Instabilities in Steel Beam-columns Under Inelastic Cyclic Straining

Hysteretic Behaviour of Shear Stud Connectors in Composite Steel Moment‐Resisting Frames

On the compressive and bond strength of reinforced concrete as structural properties

Post-tensioning of glass beams: Analytical determination of the allowable pre-load

Minimal mass design of active tensegrity structures

Investigation of fatigue damage in a RC deck slab due to moving loads through long-term monitoring of a road viaduct