Beam duct for the 1 MW neutral beam injector on TCV

About
Privacy
Disclaimer

Graph Chatbot

Related publications (32)

Page 2 of 2

JET D-T scenario with optimized non-thermal fusion

Javier García Hernández, Mikhail Maslov, Haomin Sun, Michele Marin

In JET deuterium-tritium (D-T) plasmas, the fusion power is produced through thermonuclear reactions and reactions between thermal ions and fast particles generated by neutral beam injection (NBI) heating or accelerated by electromagnetic wave heating in t ...

IOP Publishing Ltd2023

Present design of the Steering Mirror Assembly (SMA) for ITER ECHUL

Timothy Goodman, René Chavan, Anastasia Xydou

In the ITER Tokamak, four Electron Cyclotron Heating Upper Launchers (ECHUL) are needed to control plasma instabilities at the rational surfaces, most importantly the q = 3/2 and q = 2/1 neoclassical tearing modes (NTMs). Each ECHUL is equipped with a set ...

2023

Thermal Conditions in Indoor Environments: Exploring the Reasoning behind Standard-Based Recommendations

Dolaana Khovalyg, Sarah Wael Ahmed Crosby

Professionals in the building design and operation fields typically look at standards and guidelines as a reliable source of information and guidance with regard to procedural, contractual, and legal scope and requirements that are relevant to accountabili ...

2023

Characterisation of electron cyclotron wall conditioning plasma in ASDEX Upgrade

Richard Pitts

Electron cyclotron wall condition (ECWC) discharges are characterised in ASDEX Upgrade with full tungsten plasma facing components and X2 polarised waves launched from the equatorial ports, relevant to ECWC conditions in ITER Pre-Fusion Power Operation pha ...

IOP Publishing Ltd2023

Tailor-made Piezoelectric Elastomer Materials

Francis Owusu

Recent advancements in miniature devices with higher computational capabilities and ultralow power consumption have accelerated the development of wearable sensors, actuators, and energy harvesters everywhere. The ultimate aim of such a technological revol ...

EPFL2023

Tests and Qualification of the European 1 MW, 170 GHz CW Gyrotron in an ITER relevant configuration at SPC

Timothy Goodman, Stefano Alberti, Jean-Philippe Hogge, Francisco Sanchez, Jérémy Genoud

After an initial testing period at the Karlsruhe Institute of Technology, the upgraded EU 1 MW, 170 GHz continuous wave (CW) industrial prototype gyrotron (TH1509U) for Electron Cyclotron Resonance Heating and Current Drive (ECRH&CD) in ITER has been trans ...

IEEE2022

Near-junction microfluidic cooling for high power-density GaN-on-Si electronics: A wafer, device, packaging, and system-level investigation

Remco Franciscus Peter van Erp

Electrification of the energy section, from generation to end-use, plays an essential role in reducing global CO2 emission. Innovations in power electronics are required to increase conversion efficiency and power density. Gallium nitride (GaN) transistors ...

EPFL2022

Measurements of AC Loss Evolution in ITER TF Conductors

Pierluigi Bruzzone, Kamil Sedlák

AC loss in the Nb3Sn cable-in-conduit conductors (CICC) usually decreases after the conductor undergoes electromagnetic cycling. This can be attributed to the increase of inter-strand resistance due to the detachment of the strand-bonding during cyclic loa ...

IEEE Institute of Electrical and Electronics Engineers2022

Local heating and cooling effectiveness - an evaluation method based on calculated local and overall thermal state

Dolaana Khovalyg, Mohamad Rida

The application of Personal Comfort Systems (PCS) in the buildings demonstrated their potential to improve thermal comfort and reduce energy use by the space conditioning HVAC systems. With its personal controllability (on-demand) PCS is a practical soluti ...

TU Delft2022

Microchannel cooling for the LHCb VELO Upgrade I

Alessandro Mapelli

The LHCb VELO Upgrade I, currently being installed for the 2022 start of LHC Run 3, uses silicon microchannel coolers with internally circulating bi-phase CO2 for thermal control of hybrid pixel modules operating in vacuum. This is the largest scale applic ...

ELSEVIER2022

Impact of the ventilated air-space behind traditional (passive) and BIPV (active) façades on the thermo-hydrodynamic performance of the building wall structures

Mohammad Rahiminejad

For many decades, ventilated cavities in wall assemblies of buildings have been essential for creating moisture-resilient constructions by allowing airflow within the air gap to promote drying. In addition to that, the airflow in the cavity can contribute ...

EPFL2022

Heat recovery potential from ventilated passive and active facades

Dolaana Khovalyg, Mohammad Rahiminejad

A ventilated air-space behind external claddings can potentially affect the thermal performance of the entire building structure. In particular, in the Building Integrated Photovoltaic (BIPV) facades, ventilated cavities are typically present between the P ...

TU Delft OPEN2022