Measurements of internal cracking in punching test slabs without shear reinforcement

Chat with Graph Search

Ask any question about EPFL courses, lectures, exercises, research, news, etc. or try the example questions below.

DISCLAIMER: The Graph Chatbot is not programmed to provide explicit or categorical answers to your questions. Rather, it transforms your questions into API requests that are distributed across the various IT services officially administered by EPFL. Its purpose is solely to collect and recommend relevant references to content that you can explore to help you answer your questions.

Codes of practice can be overly conservative, particularly for the shear resistance of reinforced concrete beams with shear reinforcement when large loads act close to supports. This thesis addresses the topic by proposing a refined design approach based o ...

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

Ultra-high performance fiber reinforced cementitious composite (UHPFRC) is a modern class of cementitious building materials. Because of its superior mechanical properties and durability, it is increasingly used globally to rehabilitate, strengthen and mod ...

Lightweight modules are essential for next-generation vehicle-integrated photovoltaic (VIPV) applications, such as solar-powered cars, allowing integration of solar cells beyond the roof, and on the hood, boot and body panels, and thereby extending the dri ...

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

For the dimensioning and assessment of structures, it is common practice to compare action effects with sectional resistances. Extensive studies have been performed to quantify the model uncertainty on the resistance side. However, for statically indetermi ...

We investigate the failure mechanism of stopper knots, with a particular focus on the figure -8 knot as a representative example. Stopper knots are widely used in climbing, sailing, racket stringing, and sewing to maintain tension in ropes, strings, or thr ...

This research explores the capability of PEI and PVDF thermoplastic interlayers to arrest cracks in epoxy materials modified with short-glass fibers and core-shell rubber particles. It also investigates the effect of interlayer position, the number of inte ...

Every engineering calculation is an approximation of reality, with inevitable uncertainties involved. This fact implies that a reliability verification accounting for the uncertainties is a necessary step in the design and assessment of structures. Nowaday ...

Fatigue life prediction of wind turbine rotor blades is a very challenging task, as their failure is led by different failure types that act synergistically. Inherent defects like wrinkles, fiber misalignments, and voids that can be introduced during fabri ...

The aim of this paper is to argue that complementation is an operation similarly fundamental to music theory as transposition and inversion. We focus on studying the chromatic complement mapping that translates diatonic seventh chords into 8-note scales wh ...

In the evolution of structural glass beam elements, the requirements for post-fracture load bearing capacity and safe failure behaviour have led to the development of reinforced and post-tensioned beams. Maximum bending capacity in the post-fracture state ...

The Eurocode 2 for the design of concrete structures (EN1992-1-1:2004) is undergoing a revision that will lead to the publication of the second generation of this code to be used across all CEN member countries. Therefore, the impact of the code will reach ...

This paper presents the experimental results of two welded unreinforced flange-welded web (WUF-W) beam-to-column connections that defy the current design paradigm of prequalified welded connections. The proposed WUF-W connections feature customized beveled ...

The effect of fiber architecture, i.e., unidirectional (UD) vs. multi-directional (MD), on the tension-tension fa-tigue behavior of bolted double-lap basalt composite joints was experimentally investigated. The fatigue load-life (F -N) curves of MD and UD ...

Residual stresses in hot-rolled wide flange steel cross sections may lead to premature yielding, accelerated corrosion and brittle fracture of steel members. The above phenomena lead to a loss of a steel member's stiffness and resistance under mechanical l ...

Fibre-reinforced polymers (FRP) strengthening can be applied to decrease the seismic vulnerability of existing masonry buildings, both with regard to in-plane and out-of-plane failure mechanisms. Experimentally, the impact of strengthening solutions has be ...

Prequalified beam-to-column connections in steel moment resisting frames usually concentrate inelastic deformations in the steel beam ends. As such, nonlinear geo-metric instabilities (i.e., local buckling) may occur in these regions at modest lateral drif ...

Local and member instability modes in structural steel members are influenced by initial geometric imperfections and residual stresses among other parameters. The robustness of stability-related design provisions and finite element modeling procedures of s ...

Measurements of internal cracking in punching test slabs without shear reinforcement

Chat with Graph Search

Experimental and analytical investigation of shear-reinforced concrete and dowel action

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Influence of fiber orientation on the tensile behavior of UHPFRC and reinforced UHPFRC under static and fatigue loadings

Encapsulation strategies for mechanical impact and damp heat reliability improvement of lightweight photovoltaic modules towards vehicle-integrated applications

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Model uncertainties in action effects and load bearing capacity calculation in statically indeterminate reinforced concrete structures

Capsizing due to friction-induced twist in the failure of stopper knots

CRACK SHIELDING MECHANISMS OF INTERLAYERED EPOXY MATERIALS UNDER QUASI-STATIC AND FATIGUE LOADING

Reliability analysis and partial safety format calibration considering the characteristics of the resistance of reinforced concrete structures

Fatigue behavior and life prediction of wind turbine blade composite materials

Fishing for complements with chord, scale, and rhythm nets

Exploring the potential of the critical shear crack theory for reinforced and post-tensioned glass beams: Initial analysis and experiments

A Discussion on the Reliability of prEN1992-1-1:2021 Shear Strength Provisions for Fibre Reinforced Concrete Members Without Shear Reinforcement

Full-Scale Experiments of Cyclically Loaded Welded Moment Connections with Highly Dissipative Panel Zones and Simplified Weld Details

Effect of fiber architecture on tension-tension fatigue behavior of bolted basalt composite joints

Proposed residual stress model for hot‐rolled wide flange steel cross sections

Equivalent Frame Models for FRP-Strengthened Masonry Buildings

Geometric tolerances of welded connections with inelastic panel zones

Experimental Evaluation and Modeling of Residual Stress Distributions for Hot-Rolled Wide Flange Steel Members