Publication

Reinforcing hydrogels with in situ formed amorphous CaCO3

Related publications (28)

Water weakening and the compressive brittle strength of carbonates: Influence of fracture toughness and static friction

Marie Estelle Solange Violay, Barnaby Padraig Fryer, Corentin Jean-Marie Rémi Noël

Water is ubiquitous within the pore space of rocks and has been shown to affect their physical and mechanical behaviour. Indeed, water can act on the rock strength via mechanical (i.e., reducing the effective stresses) or chemical effects (e.g., mineral di ...

2024

Parametric Reduced Order Model of a Gas Bearings Supported Rotor

Jürg Alexander Schiffmann, Fabio Nobile, Dimitri Maurice Goutaudier

Gas bearings use pressurized gas as a lubricant to support and guide rotating machinery. These bearings have a number of advantages over traditional lubricated bearings, including higher efficiency in a variety of applications and reduced maintenance requi ...

2023

Additive Manufacturing of Bioinspired Mineral-Based Composites

Ran Zhao

Biominerals are used by natural organisms for example as structural supports and optical sensors. They are produced from a limited number of elements and under ambient conditions. Nevertheless, they often possess excellent mechanical properties and sometim ...

EPFL2024

Enhancing Chondrocyte Biosynthetic Activities: Harnessing the Power of Loading-Induced Evolved Temperature

Theofanis Stampoultzis

Chondrocytes within articular cartilage possess the capacity to perceive and react to signals generated by the typical load-bearing actions of daily life, such as walking or running. Articular cartilage is predominantly oriented toward compression-based fu ...

EPFL2024

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Xhemsi Malja

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

RE:SLAB — a load bearing system for open-ended component reuse in building structures

Dario Redaelli, Corentin Jean Dominique Fivet, Jan Friedrich Georg Brütting, Alex-Manuel Muresan, Edisson Xavier Estrella Arcos

The construction industry plays a major role in the high levels of greenhouse gas emissions, resource consumption, and waste generation observed nowadays. Key to the circular economy, structural component reuse arises as a promising solution to divert cons ...

2024

Localized Ionic Reinforcement of Double Network Granular Hydrogels

Esther Amstad, Alexandra Thoma

Nature produces soft materials with fascinating combinations of mechanical properties. For example, the mussel byssus embodies a combination of stiffness and toughness, a feature that is unmatched by synthetic hydrogels. Key to enabling these excellent mec ...

Wiley-V C H Verlag Gmbh2024

Multiscale Spatiotemporal Characterization of Embodied Environmental Performance of Building Structures in Geneva from 1850 to 2018

Corentin Jean Dominique Fivet, Catherine Elvire L. De Wolf, Serena Vanbutsele

Load-bearing systems in buildings, significant in material use and embodied greenhouse gas emissions (EGHGE), have lacked detailed analysis on their environmental and functional relationships over time and space. This study evaluates the environmental impa ...

2024

Numerical investigation of two-dimensional Mode-II delamination in composite laminates

Thomas Keller, Anastasios Vassilopoulos, Congzhe Wang

Existing standards for delamination tests on composite materials typically employ one-dimensional (1D) beam specimens. However, such specimens may not represent real delamination scenarios in composite structures, where cracks tend to propagate in two dime ...

Elsevier Sci Ltd2024

Model uncertainties in action effects and load bearing capacity calculation in statically indeterminate reinforced concrete structures

Alain Nussbaumer, Aurelio Muttoni, Xhemsi Malja

For the dimensioning and assessment of structures, it is common practice to compare action effects with sectional resistances. Extensive studies have been performed to quantify the model uncertainty on the resistance side. However, for statically indetermi ...

Ernst & Sohn2024

Controlling the Microstructure and Composition of 3D Printed Soft Load-Bearing Hydrogels

Matteo Hirsch

Hydrogels are among the first materials expressly designed for their use in biomedicine. However, state-of-the-art applications of hydrogels are severely limited because they are typically either too soft or too brittle such that they cannot bear significa ...

EPFL2023

Exploring the potential of the critical shear crack theory for reinforced and post-tensioned glass beams: Initial analysis and experiments

Alain Nussbaumer, Pieter Christian Louter, Jagoda Cupac

In the evolution of structural glass beam elements, the requirements for post-fracture load bearing capacity and safe failure behaviour have led to the development of reinforced and post-tensioned beams. Maximum bending capacity in the post-fracture state ...

2023

Parametric Reduced Order Model of a Gas Bearings Supported Rotor

Jürg Alexander Schiffmann, Fabio Nobile, Dimitri Maurice Goutaudier

Amer Soc Mechanical Engineers2023

Three-dimensional hydraulic fracture propagation in homogeneous and heterogeneous media

Carlo Peruzzo

Hydraulic fractures are tensile fractures that occur in solid materials due to the natural intrusion or anthropogenic injection of a viscous fluid into a fracture channel. The deliberate creation of hydraulic fractures is part of an industrial technology h ...

EPFL2023

Interactive design with optimum matchmaking of reused structural elements – a software implementation

Corentin Jean Dominique Fivet, Jan Friedrich Georg Brütting, Jonas Warmuth

Structural systems are a significant contributor to buildings’ embodied carbon and reusing structural elements in new load-bearing applications is one strategy to reduce this impact. However, integrating this approach into existing design workflows without ...

International Association for Shell and Spatial Structures (IASS)2023

Graph neural networks for dynamic modeling of roller bearings

Olga Fink, Vinay Sharma

Machine learning has paved the way for the real-time monitoring of complex infrastructure and industrial systems. However, purely data-driven methods have not been able to learn the underlying dynamics and generalize them to operating conditions that have ...

PHM Society2023

Robust Design of Herringbone Grooved Journal Bearings using Multi-Objective Optimization with Artificial Neural Networks

Jürg Alexander Schiffmann, Soheyl Massoudi

Herringbone grooved journal bearings (HGJBs) are widely used in micro-turbocompressor applications due to their high load-carrying capacity, low friction, and oil-free solution. However, the performance of these bearings is sensitive to manufacturing devia ...

2023

Robust Design of Herringbone Grooved Journal Bearings using Multi-Objective Optimization with Artificial Neural Networks

Jürg Alexander Schiffmann, Soheyl Massoudi

Amer Soc Mechanical Engineers2023

4D printing of Metal-Reinforced double network granular hydrogels

Esther Amstad, Matteo Hirsch, Josephine Anna Eleanor Hughes, Qinghua Guan, Livia D'Onofrio

Recent developments in soft actuation demand for resilient, responsive materials with locally varying compositions that are sufficiently stiff to exhibit significant actuation forces. Hydrogels are inherently responsive to certain stimuli. Yet, they typica ...

2023

An Integrated Approach to Designing Robust Turbocompressors on Gas Bearings Through Surrogate Modeling and Constrained Multi-Objective Optimization

Jürg Alexander Schiffmann, Cyril Picard, Soheyl Massoudi

Designing turbocompressors is a complex and challenging task, as it involves balancing conflicting objectives such as efficiency, stability, and robustness against manufacturing deviations. This paper proposes an integrated design methodology for turbocomp ...

ASME Amer Soc Mechanical Engineers2023