Publications related to Insights into the fabrication of sub-100 nm textured thermally drawn fibers

Related publications (38)

Quench Detection and Temperature Measurement With Fiber Optic Sensors

For the EU DEMO conductor testing, a temperature sensor based on Fiber Bragg Grating (FBG) optical fiber is studied at the EPFL Swiss Plasma Center. The SULTAN test facility has been upgraded to use fiber optic sensor for temperature monitoring and quench ...

IEEE Institute of Electrical and Electronics Engineers2024

Highly anisotropic carbon fiber electrodes for DEAs and their dynamic non-monotonic conductive properties

Yves Perriard, Stefania Maria Aliki Konstantinidi

A common method for creating compliant electrodes for dielectric elastomer actuators (DEAs) and soft sensors is to incorporate electrically conductive carbon particles into a polymer matrix. However, using unidirectional aligned carbon fibers instead not o ...

Society of Photo-Optical Instrumentation Engineers (SPIE)2024

Computational fluid dynamics simulations of the heat transfer properties of graphene-based nanolubricants and application to hydrodynamic lubrication

Roberto Guarino

In this paper, we consider experimental data available for graphene-based nanolubricants to evaluate their convective heat transfer performance by means of computational fluid dynamics (CFD) simulations. Single-phase models with temperature-dependent prope ...

Aip Publishing2024

Process development of pre-impregnated hybrid thin-ply composites

Alexios Argyropoulos

Thin-ply composites, obtained with recently developed fiber spreading techniques, rapidly gained industrial interest because they offer a large composite design freedom, and lead to a composite tensile strength that is close to that of the individual fiber ...

EPFL2023

Self-powered transformer intelligent wireless temperature monitoring system based on an ultra-low acceleration piezoelectric vibration energy harvester

Xin Chen

The wireless sensor nodes used for monitoring the condition of grid equipment always be powered by disposable batteries. However, it introduces disadvantages, such as inconvenient replacement, short lifespan, and envi-ronmental pollution, significantly imp ...

Elsevier2023

Multi-scale characterization and modeling of notched strength and translaminar fracture in hybrid thin-ply composites based on different carbon fiber grades

Guillaume Clément Broggi

Owing to their high specific stiffness and strength, Carbon Fiber Reinforced Composites (CFRP) are ideal candidates for the development of lightweight high-performance structures. Within this family, thin-ply composites allow for wider design freedom and p ...

EPFL2023

Semiconductor-based device architectures in multimaterial fibers

William Nicolas Duncan Esposito

Semiconductor materials have given rise to today's digital technology and consumer electronics. Widespread adoption is closely linked to the ability to process and integrate them in devices at scale. Where flexibility and large surfaces are required, such ...

EPFL2023

Confirming the high pressure phase diagram of the Shastry-Sutherland model

Henrik Moodysson Rønnow, Martin Mansson

A Muon Spin Rotation (mu+SR) study was conducted to investigate the magnetic properties of SrCu2(BO3)(2) (SCBO) as a function of temperature/pressure. Measurements in zero field and transverse field confirm the absence of long range magnetic order at high ...

IOP PUBLISHING LTD2023

Thermally Drawn Elastomer Nanocomposites for Soft Mechanical Sensors

Fabien Sorin, Yunpeng Qu, Andreas Leber, Inès Richard, Chaoqun Dong, Stella Andréa Françoise Laperrousaz

Stretchable and conductive nanocomposites are emerging as important constituents of soft mechanical sensors for health monitoring, human-machine interactions, and soft robotics. However, tuning the materials' properties and sensor structures to the targete ...

WILEY2023

Permeability sets the linear path instability of buoyancy-driven disks

François Gallaire, Pier Giuseppe Ledda, Giuseppe Antonio Zampogna

The prediction of trajectories of buoyancy-driven objects immersed in a viscous fluid is a key problem in fluid dynamics. Simple-shaped objects, such as disks, present a great variety of trajectories, ranging from zig-zag to tumbling and chaotic motions. Y ...

Cambridge University Press2023

Effect of wettability and textile architecture on fluid displacement and pore formation during infiltration of carbon fibrous preforms

Véronique Michaud, Baris Çaglar, Helena Luisa Teixido Pedarros

We seek to address how air entrapment mechanisms during infiltration are influenced by the wetting characteristics of the fluid and the pore network formed by the reinforcement. To this end, we evaluated the behavior of two model fluids with different surf ...

Elsevier Sci Ltd2023

Cotton yarns decorated with hydrothermally reduced graphene oxide for flexible supercapacitors

Dou Du

Cotton fibers, a natural cellulose, have played a critical role in the development of wearable energy storage, owning to their wearability, integrability, eco-benignity, and cost effectiveness. Graphene, a two-dimensional carbon material, possesses excelle ...

Elsevier2023

The Development of Aptamer-Coupled Microelectrode Fiber Sensors (apta-?FS) for Highly Selective Neurochemical Sensing

Fabien Sorin

The selective and sensitive sensing of neurochemicals is essential to decipher in-brain chemistry underlying brain pathophysiology. The recent development of flexible and multifunctional polymer-based fibers has been shown useful in recording and modulatin ...

AMER CHEMICAL SOC2023

Thermally Drawn CNT-Based Hybrid Nanocomposite Fiber for Electrochemical Sensing

Fabien Sorin, Inès Richard

Nowadays, bioelectronic devices are evolving from rigid to flexible materials and substrates, among which thermally-drawn-fiber-based bioelectronics represent promising technologies thanks to their inherent flexibility and seamless integration of multi-fun ...

MDPI2022

Analysis and modelling of momentum transport based on NBI modulation experiments at ASDEX Upgrade

Basil Duval, Emiliano Fable

The prediction of plasma rotation is of high interest for fusion research due to the effects of the rotation upon magnetohydrodynamic (MHD) instabilities, impurities, and turbulent transport in general. In this work, an analysis method was studied and vali ...

2022

Non-destructive Prediction of the Buckling Load of Cylindrical Shells

Emilio José Lozano Vazquez

The current research focuses on the prediction of the maximum axial compression load a cylindrical shell is able to bear. This maximum axial compression load is the value at which a cylindrical shell loses stability and abruptly buckles. After the buckling ...

EPFL2022

A life cycle analysis of novel lightweight composite processes: Reducing the environmental footprint of automotive structures

Véronique Michaud, Baris Çaglar, Vincent Werlen, Colin Gomez

In this study, three novel thermoplastic impregnation processes were analyzed towards automotive applications. The first process is thermoplastic compression resin transfer molding in which a glass fiber mat is impregnated in through thickness by a thermop ...

ELSEVIER SCI LTD2022

Cyclic Behaviour of Unidirectional Hybrid Interlayer Glass/Carbon and Carbon/Carbon Composites

Anastasios Vassilopoulos

The lack of ductility is a major drawback of fibre reinforced polymer (FRP) materials. As it is known, these materials are stiff and strong, but brittle with little or no warning before final failure. In the last decades, some solutions have been proposed ...

SPRINGER-VERLAG SINGAPORE PTE LTD2022

Runaway dynamics in reactor-scale spherical tokamak disruptions

Carl Mathias Paul Hoppe

Understanding generation and mitigation of runaway electrons in disruptions is important for the safe operation of future tokamaks. In this paper we investigate the runaway dynamics in reactor-scale spherical tokamaks, focusing on a compact nominal design ...

Cambridge University Press2022

Monitoring of Torque Induced Strain in Composite Shafts with Embedded and Surface-Mounted Optical Fiber Bragg Gratings

John Botsis, Georgios Violakis, Georgios Pappas

In this study, silica glass, optical fiber Bragg gratings (FBGs) are used for torque-induced strain monitoring in carbon fiber reinforced polymer (CFRP) hollow shafts toward the development of a methodology for structural load monitoring. Optical fibers wi ...

2021