Publications related to Non-symmetrical punching of flat slabs and slab bridges without transverse reinforcement

Related publications (29)

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Diego Hernández Fraile

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

EPFL2024

Experimental and analytical investigation of shear-reinforced concrete and dowel action

Marko Pejatovic

Codes of practice can be overly conservative, particularly for the shear resistance of reinforced concrete beams with shear reinforcement when large loads act close to supports. This thesis addresses the topic by proposing a refined design approach based o ...

EPFL2024

Estimation of the bar stress based on crack width measurements in reinforced concrete structures

Aurelio Muttoni, Enrique Corres Sojo

Estimating the stress of reinforcing bars and its variations in service conditions can be useful to determine the reserve capacity of structures or to assess the risk of fatigue in the reinforcement. This paper investigates the use crack width measurements ...

Ernst & Sohn2024

Insights from an extensive triaxial testing campaign on a shale for comparative site characterization of a deep geological repository

Lyesse Laloui, Alessio Ferrari, Eleonora Crisci

Several boreholes were drilled for site comparison of a deep geological repository (DGR) in Northern Switzerland. The main target of the exploration program was the >100m thick Opalinus Clay, the designated host rock encountered at approximately 450 to 100 ...

Elsevier2024

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Landolf-Giosef-Anastasios Rhode-Barbarigos, Tara Habibi

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

2024

Experimental investigation of dowel action in reinforcing bars using refined measurements

Aurelio Muttoni, Marko Pejatovic

In typical reinforced concrete design, reinforcement is designed to carry axial forces, but it can also resist transversal forces by dowel action. This is usually neglected for simplicity's sake in the design phase, but it can be accounted for either expli ...

Ernst & Sohn2024

Micro modeling of irregular stone masonry walls using mathematical programming

Katrin Beyer, Qianqing Wang, Ketson Roberto Maximiano Dos Santos

While understanding the shear strength of stone masonry structures is important for the design and the mainte- nance, we still lack computational tools for predicting the strength as a function of the stone layout. Here we implement an end-to-end image bas ...

Springer2024

Two-dimensional quasi-static delamination in composite laminates under Mode-I and Mode-II conditions

Congzhe Wang

Fiber-polymer composites consist of a polymer matrix and reinforcing fibers made of various materials. These composites exhibit exceptional properties, such as a high strength-to-weight ratio and excellent corrosion resistance, which has led to their incre ...

EPFL2024

Contributions to rebar-to-concrete interaction and its structural implications for design and monitoring applications

Enrique Corres Sojo

Bond between reinforcing bars and concrete has been the focus of extensive research over the last century. This is well-justified as the functioning of reinforced concrete intimately depends on the interaction between rebar and concrete, as for example cra ...

EPFL2024

Water weakening and the compressive brittle strength of carbonates: Influence of fracture toughness and static friction

Marie Estelle Solange Violay, Corentin Jean-Marie Rémi Noël, Barnaby Padraig Fryer

Water is ubiquitous within the pore space of rocks and has been shown to affect their physical and mechanical behaviour. Indeed, water can act on the rock strength via mechanical (i.e., reducing the effective stresses) or chemical effects (e.g., mineral di ...

2024

Numerical Modeling of FRP-Strengthened Masonry Structures Using Equivalent Frame Models

Katrin Beyer, Francesco Vanin, Ivana Bozulic

The present study focuses on enhancing the seismic resistance of existing masonry structures. To that aim, the use of fiber-reinforced polymer (FRP) strengthening serves to improve structural behaviour by attaching FRP strips to the masonry walls. Despite ...

Springer2024

Influence of fiber orientation on the tensile behavior of UHPFRC and reinforced UHPFRC under static and fatigue loadings

Jian Zhan

Ultra-high performance fiber reinforced cementitious composite (UHPFRC) is a modern class of cementitious building materials. Because of its superior mechanical properties and durability, it is increasingly used globally to rehabilitate, strengthen and mod ...

EPFL2024

Decarbonization potential of steel fibre-reinforced limestone calcined clay cement concrete one-way slabs

Hisham Tarek Mohamed Hafez, Beatrice Malchiodi

This study deals with a comparison of the environmental performance of one-way slabs utilizing steel fibrereinforced limestone calcined clay cement (LC3) concrete with the control case of Ordinary Portland cement concrete. The experimental program constitu ...

Elsevier Sci Ltd2024

Reusability assessment of reinforced concrete components prior to deconstruction from obsolete buildings

Corentin Jean Dominique Fivet, Maléna Bastien Masse, Julie Rachel Devènes

A large part of building demolitions is motivated by purely socio-economic reasons. Hence, about-to-be-demolished structures, commonly made of reinforced concrete, very often present no or little degradation. When adaptive reuse of the entire building is n ...

2024

Additively manufactured steel reinforcement for small scale reinforced concrete modeling: Tensile and bond behavior

Christian Leinenbach

Small scale (1:30-1:40) Reinforced Concrete is useful for centrifuge testing. However, manufacturing the reinforcing cages by hand at this scale is practically difficult. This paper suggests that small scale reinforcement can be manufactured using a metal ...

Elsevier Sci Ltd2024

Numerical investigation of two-dimensional Mode-II delamination in composite laminates

Thomas Keller, Anastasios Vassilopoulos, Congzhe Wang

Existing standards for delamination tests on composite materials typically employ one-dimensional (1D) beam specimens. However, such specimens may not represent real delamination scenarios in composite structures, where cracks tend to propagate in two dime ...

Elsevier Sci Ltd2024

An adaptive phase field approach to 3D internal crack growth in rocks

Tao Xu, Michael Heap, Alexandra Roma Larisa Kushnir

Modeling the 3D internal crack under compression entails complex fracture mechanics (mode I-II-III fracture), resulting in substantial computational costs and challenges in characterizing fracture morphology characterization for Phase Field Method (PFM) si ...

2024

A concrete answer for circular construction: three prototypes reusing saw-cut elements

Corentin Jean Dominique Fivet, Maléna Bastien Masse, Célia Marine Küpfer

Existing concrete buildings should be retained for as long as possible to reduce the environmental burden of demolition and new construction. However, when urban pressure makes demolition unavoidable, salvaging and reusing concrete elements elsewhere in ne ...

2024

Dataset for "Complexity of crack front geometry enhances toughness of brittle solids"

John Martin Kolinski, Chenzhuo Li, Xinyue Wei

This data package supports the publication 'Complexity of crack front geometry enhances toughness of brittle solids' by Xinyue Wei, Chenzhuo Li, Cían McCarthy, and John M. Kolinski Nature physics (2024) - https://doi.org/10.1038/s41567-024-02435-x DOI: 1 ...

Zenodo2024