Publication

Fabrication of Free-Standing Plasmonic Nanoantennas with Application for Optical Break Junctions

Related publications (28)

Additively manufactured stretchable zipping electrostatic actuators

The use of soft and stretchable materials allows the development of adaptive robotic systems and human-machine interfaces that are more natural and comfortable to interact with. One of the application fields that benefits the most from these compliant mate ...

EPFL2024

Silicon microresonator arrays: A comprehensive study on fabrication techniques and pH-controlled stress-induced variations in cantilever stiffness

Luis Guillermo Villanueva Torrijo, Annalisa De Pastina

We introduce a detailed design and fabrication process of Silicon microcantilever arrays for biomolecular detection in liquid environment, utilized with laser readout. We present typical fabrication problems and provide related solutions to obtain high qua ...

Elsevier2024

Advanced Silicon and SWIR Single-Photon Avalanche Diodes: Design, Simulation, and Characterization

Ekin Kizilkan

Low-level light detection with high spatial and timing accuracy is a growing area of interest by virtue of applications such as light detection and ranging (LiDAR), biomedical imaging, time-resolved Raman spectroscopy, and quantum applications. Single-phot ...

EPFL2024

Evaluation of Interface and Residual Strain of NiTi Layer Deposited on NiTiX Substrate by Laser Powder Bed Fusion

Elyas Ghafoori, Christian Leinenbach, Irene Ferretto, Mahbod Golrang, Mahshid Memarian

This study investigates the microstructure and properties of functionally graded NiTi alloy bilayers. The NiTi layer is printed by laser powder bed fusion on a NiTiX (where X is Hf or Cu) substrate prepared by vacuum arc remelting. Specimens produced with ...

Wiley-V C H Verlag Gmbh2024

An Ultralow-Power Triaxial MEMS Accelerometer With High-Voltage Biasing and Electrostatic Mismatch Compensation

Yimai Peng, Li Xu, Kyojin Choo

This article presents a triaxial micro electromechani-cal system (MEMS) capacitive accelerometer using a high-voltage biasing technique to achieve high resolution with ultralow power. The accelerometer system generates a differential pair of high voltages ...

Ieee-Inst Electrical Electronics Engineers Inc2024

Zinc hybrid sintering for printed transient sensors and wireless electronics

Danick Briand, Nicolas Francis Fumeaux

Transient electronics offer a promising solution for reducing electronic waste and for use in implantable bioelectronics, yet their fabrication remains challenging. We report on a scalable method that synergistically combines chemical and photonic mechanis ...

2023

A multi-material robotic finger with integrated proprioceptive and tactile capabilities produced with a circular process

Antonia Georgopoulou Papadonikolaki, Josephine Anna Eleanor Hughes, Kai Christian Junge

When developing or designing biomimetic robotic fingers with rigid and soft components and integrated sensors, fabrication is often a bottle-neck when assembling and casting processing techniques are used. This study introduces a thermoplastic multi-materi ...

IEEE2023

First developments towards producing inductive magnetic sensors using state-of-the-art photolithography techniques

Duccio Testa, Ambrine Douhane, Marcus Cemes

Inductive magnetic sensors are needed for tokamak operation to provide the low-frequency (LF) measurements leading to the equilibrium reconstruction and to monitor the higher frequency (HF) instabilities; the HF magnetic sensors are often also used as a ba ...

2023

Additive and digital manufacturing of transient sensors and bioelectronics

Nicolas Francis Fumeaux

Transient electronics have emerged as a promising class of devices, capable of breaking down without harmful side effects to their environment. They have tremendous potential as bioresorbable electronics for temporary applications in the human body, and as ...

EPFL2023

Volumetric additive manufacturing in a scattering resin

Jorge Andres Madrid Wolff

Volumetric 3D printing is a novel technique that offers promising new perspectives in tissue engineering. In volumetric 3D printing, photosensitive gels or liquids are solidified by projecting light patterns via reverse tomography. Recent results show that ...

EPFL2023

Printed degradable piezoelectric microsystems: From ink formulation to device fabrication and characterization

Morgan Mc Kay Monroe

As the world moves further and further into the semiconductor era, the amount of waste generated from electronics ("e-waste") is increasing rapidly and unsustainably. Of particular note, alternatives to lead-based piezoelectric materials must be establishe ...

EPFL2023

Selective Growth of van der Waals Heterostructures Enabled by Electron-Beam Irradiation

Aleksandra Radenovic, Michal Daniel Macha

Van der Waals heterostructures (vdWHSs) enable the fabricationof complex electronic devices based on two-dimensional (2D) materials.Ideally, these vdWHSs should be fabricated in a scalable and repeatableway and only in the specific areas of the substrate t ...

AMER CHEMICAL SOC2023

Fab-to-fab and run-to-run variability in 130 nm and 65 nm CMOS technologies exposed to ultra-high TID

Jean-Michel Sallese, Adil Koukab, Stefano Michelis, Gennaro Termo

The discovery of a large fab-to-fab variability in the TID response of the CMOS technologies used in the design of ASICs for the particle detectors of the HL-LHC triggered a monitoring effort to verify the consistency of the CMOS production process over ti ...

IOP Publishing Ltd2023

Reinforcement learning for scaffold-free construction of spanning-structures

Gabriel Rémi Vallat, Anna Maria Maddux, Jingwen Wang, Maryam Kamgarpour, Stefana Parascho

In construction robotics, a conventional design-to-fabrication work-flow starts with designing a structure, followed by task and robotic motion planning, and ultimately, fabrication. However, this approach can prove unsuccessful, as we may only discover th ...

New York2023

The physics of 3D printing with light

Christophe Moser

The goal of 3D printing is to realize complex 3D structures by locally adding material in small volume elements called voxels - in contrast to successively subtracting material by etching, milling or machining. This field started with optics-based proposal ...

Nature Portfolio2023

Semiconductor-based device architectures in multimaterial fibers

William Nicolas Duncan Esposito

Semiconductor materials have given rise to today's digital technology and consumer electronics. Widespread adoption is closely linked to the ability to process and integrate them in devices at scale. Where flexibility and large surfaces are required, such ...

EPFL2023

Scalable fabrication of functional nanostructures on stretchable substrates by capillary-assisted particle assembly and adhesion lithography

Henry Shao-Chi Yu

The fabrication of metallic nanostructures on stretchable substrates enables specific applications that exploit the combination of the nano-scale phenomena and the mechanical tunability of the physical dimensions of the nanostructures. Due to the large dif ...

EPFL2022

A new versatile hybrid MEMS technology for high sensitivity, fluid proof sensing applications

Matthias Neuenschwander

The field of micro electromechanical systems (MEMS) evolved from the microelectronic industry and the technologies developed to fabricate integrated circuits. As a result, MEMS are commonly fabricated on silicon wafers. The development of MEMS has been dri ...

EPFL2022

Additive manufacturing of ceramics by two-photon lithography, volumetric 3D printing and high-resolution endo-printing

Georgia Konstantinou

Additive manufacturing is a growing sector of industrial production that allows the fabrication of parts with complex geometries and reduced waste. The context of this thesis is light-based additive manufacturing technologies. In the first part of the the ...

EPFL2022

A Variable Stiffness Magnetic Catheter Made of a Conductive Phase-Change Polymer for Minimally Invasive Surgery

Dario Floreano, Jun Shintake, Yegor Piskarev

Variable stiffness (VS) is an important feature that significantly enhances the dexterity of magnetic catheters used in minimally invasive surgeries. Existing magnetic catheters with VS consist of sensors, heaters, and tubular structures filled with low me ...

2022