Publications related to The Effect of Limestone on the Performance of Ternary Blended Cement LC3: Limestone, Calcined Clays and Cement

Related publications (32)

Micro modeling of irregular stone masonry walls using mathematical programming

Katrin Beyer, Qianqing Wang, Ketson Roberto Maximiano Dos Santos

While understanding the shear strength of stone masonry structures is important for the design and the mainte- nance, we still lack computational tools for predicting the strength as a function of the stone layout. Here we implement an end-to-end image bas ...

Springer2024

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Xhemsi Malja

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Water weakening and the compressive brittle strength of carbonates: Influence of fracture toughness and static friction

Marie Estelle Solange Violay, Corentin Jean-Marie Rémi Noël, Barnaby Padraig Fryer

Water is ubiquitous within the pore space of rocks and has been shown to affect their physical and mechanical behaviour. Indeed, water can act on the rock strength via mechanical (i.e., reducing the effective stresses) or chemical effects (e.g., mineral di ...

2024

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Landolf-Giosef-Anastasios Rhode-Barbarigos, Tara Habibi

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

2024

Insights from an extensive triaxial testing campaign on a shale for comparative site characterization of a deep geological repository

Lyesse Laloui, Alessio Ferrari, Eleonora Crisci

Several boreholes were drilled for site comparison of a deep geological repository (DGR) in Northern Switzerland. The main target of the exploration program was the >100m thick Opalinus Clay, the designated host rock encountered at approximately 450 to 100 ...

Elsevier2024

Durability Challenges of Low-Grade Calcined Clay Opposed to High-Volume Fly Ash in General Purpose Concrete

Karen Scrivener

With the decrease in availability of common supplementary cementitious materials (SCMs) such as fly ash in Europe, the search for appropriate SCMs should be dealt with locally. A com-bination of abundant low-grade calcined clay and limestone powder has pro ...

AMER SOC TESTING MATERIALS2023

Influence of temperature on phase assemblages of belite-ye'elimite cement

Karen Scrivener, Diana Londoño Zuluaga, Natechanok Chitvoranund

This paper studies the effect of temperature on the phase assemblages of belite-ye'elimite cement. A comparison is made between thermodynamic modelling and experimental data at 28 and 180 days of hydration at 5, 20, 40, and 60 degrees C. The fast reaction ...

Pergamon-Elsevier Science Ltd2023

Influence of Low- to Medium-Kaolinite Clay on the Durability of Limestone Calcined Clay Cement (LC3) Concrete

Karen Scrivener

The kaolinite content is principally responsible for the durability performance of Limestone Calcined Clay Cement (LC3), which calls into question its global applicability. The clay supply has a significant impact on the LC3 system's reduced carbon footpri ...

MDPI2023

The role of Zn in C-S-H atomic structure, nucleation and growth

Anna Morales Melgares

The most promising solution towards cementitious materials with a lower carbon footprint is the partial substitution of the clinker by supplementary cementitious materials (SCMs) such as fly ash, blast furnace slag, limestone and calcined clays. The produc ...

EPFL2023

Role of Minimum Adhesive Wear Particle Size in Third-Body Layer Properties

Jean-François Molinari, Son-Jonathan Pham-Ba

We employ a novel discrete element method (DEM) force formulation to simulate adhesive wear and assess the effects of material and loading parameters on the properties of the third-body layer (TBL) formed during sliding motion. The study emphasizes the rol ...

2023

A Discussion on the Reliability of prEN1992-1-1:2021 Shear Strength Provisions for Fibre Reinforced Concrete Members Without Shear Reinforcement

Miguel Fernández Ruiz

The Eurocode 2 for the design of concrete structures (EN1992-1-1:2004) is undergoing a revision that will lead to the publication of the second generation of this code to be used across all CEN member countries. Therefore, the impact of the code will reach ...

SPRINGER INTERNATIONAL PUBLISHING AG2023

Going Below 50% Clinker Factor in Limestone Calcined Clay Cements (LC3): A Comparison with Pozzolanic Cements from the South American Market

Karen Scrivener, Franco Alberto Zunino Sommariva

Limestone calcined clays are a promising technology as they offer similar performance to OPC from 7 days onwards, while enabling a reduction of the clinker content of 50%. In some regions of the world like South America, pozzolanic cements (i.e., blended c ...

SPRINGER INTERNATIONAL PUBLISHING AG2023

Incorporation of Lignin in Bio-Based Resins for Potential Application in Fiber-Polymer Composites

Mateus De Assunção Hofmann

Bio-based resins, obtained from renewable raw materials, are a more sustainable alternative to oil-based resins for fiber-reinforced polymer (FRP) composites. The incorporation of lignin in those resins has the potential to enhance their performance. This ...

MDPI2023

Simultaneous strength and ductility enhancement of wire-arc directed energy deposited Al-Cu alloy by interlayer laser shock peening

Ke Huang, Yandong Jing

Wire-arc directed energy deposition (wire-arc DED), recognized for its ability to produce large-scale parts, has gained considerable attention. However, a critical issue with this method is the high prevalence of internal porosity defects found in the manu ...

Elsevier Science Sa2023

Energy dissipation in fiber-polymer composites adhesive joints under cyclic loading

Ghazaleh Eslami

Sustainable development has emerged as a paramount consideration in various fields of industry, including construction, to preserve the environment and its finite resources. Lightweight structures, such as fiber-polymer composite structures, address both s ...

EPFL2023

Atomistic modeling of C-S-H: bulk and surface

Ziga Casar

By replacing part of Portland cement with so-called supplementary cementitious materials (SCMs) it is possible to reduce the CO2 footprint of the cement industry. These SCMs are commonly limestone, calcined clay, slag and fly ash. While doing so the early ...

EPFL2023

The strength of surgical knots involves a critical interplay between friction and elastoplasticity

Pedro Miguel Nunes Pereira de Almeida Reis, Paul Johanns, Paul Grandgeorge

Knots are the weakest link in surgical sutures, serving as mechanical ligatures between filaments. Exceeding their safe operational limits can cause fatal complications. The empirical nature of present guidelines calls for a predictive understanding of the ...

AMER ASSOC ADVANCEMENT SCIENCE2023

Multi-scale characterization and modeling of notched strength and translaminar fracture in hybrid thin-ply composites based on different carbon fiber grades

Guillaume Clément Broggi

Owing to their high specific stiffness and strength, Carbon Fiber Reinforced Composites (CFRP) are ideal candidates for the development of lightweight high-performance structures. Within this family, thin-ply composites allow for wider design freedom and p ...

EPFL2023

Process development of pre-impregnated hybrid thin-ply composites

Alexios Argyropoulos

Thin-ply composites, obtained with recently developed fiber spreading techniques, rapidly gained industrial interest because they offer a large composite design freedom, and lead to a composite tensile strength that is close to that of the individual fiber ...

EPFL2023

Quantitative study of the thickness-dependent stress in indium tin oxide thin films

Blaise François Cuénod, Rémy David Désiré Juttin

A quantitative analysis of stress in indium tin oxide (ITO) films with varying thicknesses was conducted using high-precision stylus profilometry. The experimental results revealed a transition of the stress type from tensile to compressive as the ITO film ...

Elsevier Science Sa2023