Publications related to Development of High-Strength Aluminum Alloys for Additive Manufacturing

Related publications (31)

Effects of Rate-dependent Plasticity on Residual Stresses in Additive Manufacturing of Complex Alloys

The recent introduction of high entropy alloys presents an exciting opportunity for novel material performance, offering extensive possibilities for tailoring material properties. Dislocation mechanisms in these alloys must be fully understood since they p ...

EPFL2025

Dislocation Hardening in a New Manufacturing Route of Ferritic Oxide Dispersion-Strengthened Fe-14Cr Cladding Tube

Roland Logé

The microstructure evolution associated with the cold forming sequence of an Fe-14Cr-1W-0.3Ti-0.3Y2O3 grade ferritic stainless steel strengthened by dispersion of nano oxides (ODS) was investigated. The material, initially hot extruded at 1100 degrees C an ...

MDPI2024

Composition and Element Distribution Mapping of γ′ and γ" Phases of Inconel 718 by High-Resolution Scanning Transmission Electron Microscopy and X-ray Energy-Dispersive Spectrometry

Philippe Buffat

The main strengthening mechanism for Inconel 718 (IN718), a Ni-based superalloy, is precipitation hardening by gamma ' and gamma '' particles. It is thus essential, for good alloy performance, that precipitates with the desired chemical composition have ad ...

MDPI2024

Performance of energy piles foundation in hot-dominated climate: A case study in Dubai

Lyesse Laloui, Elena Ravera, Sofie Elaine ten Bosch

Energy piles represent an innovative technology that can help provide sustainable geothermal heating or cooling energy for thermal conditioning purposes. In hot-dominated climates, the interest is to inject heat in the ground and extract energy for space-c ...

Pergamon-Elsevier Science Ltd2024

Design and assessment of an evaporating water-cooled methanation reactor for a SOE-based power-to-methane system

Philippe Aubin

The transition towards clean renewable energy sources, where wind and solar are prone to variation, requires adequate energy storage. Power-to-methane (PtM) systems can be part of the solution. Specifically, solid-oxide-electrolyser (SOE) based PtM systems ...

EPFL2024

Solute-strengthening in metal alloys with short-range order

William Curtin, Shankha Nag

Recent surging interest in strengthening of High Entropy Alloys (HEAs) with possible chemical ordering motivates the development of new theory. Here, an existing theory for random alloys that accounts for solute-dislocation and solute–solute interactions i ...

2024

Flash Melting Amorphous Ice

Marcel Drabbels, Ulrich Lorenz, Gabriele Bongiovanni, Constantin Richard Krüger, Nathan Junior Mowry

Water can be vitrified if it is cooled at high rates, which makes it possible to outrun crystallization in so-called no man’s land, a range of deeply supercooled temperatures where water crystallizes rapidly. Here, we study the reverse process in pure wate ...

2024

Evaluation of Interface and Residual Strain of NiTi Layer Deposited on NiTiX Substrate by Laser Powder Bed Fusion

Elyas Ghafoori, Christian Leinenbach, Irene Ferretto

This study investigates the microstructure and properties of functionally graded NiTi alloy bilayers. The NiTi layer is printed by laser powder bed fusion on a NiTiX (where X is Hf or Cu) substrate prepared by vacuum arc remelting. Specimens produced with ...

Wiley-V C H Verlag Gmbh2024

First-principles thermodynamics of precipitation in aluminum-containing refractory alloys

Anirudh Raju Natarajan

Materials for high -temperature environments are actively being investigated for deployment in aerospace and nuclear applications. This study uses computational approaches to unravel the crystallography and thermodynamics of a promising class of refractory ...

Pergamon-Elsevier Science Ltd2024

Decomposition method to evaluate district heating/cooling network potential at urban scale

Ana Catarina Gouveia Braz, François Maréchal, Luc Girardin, Bingqian Liu

In this work, a tool to design district heating networks (DHN) is presented and applied to the city of Lausanne as a case study. The evaluation of the buildings’ heat/cooling demand is performed using a Geographic Information System (GIS) database, built f ...

Associazione Italiana Di Ingegneria Chimica2024

Design for demise applied to spacecraft structural panels and experiments for ClearSpace One platform

Alexandre Achille Looten

With growing awareness of the vulnerability of the near-Earth space region and the anticipated surge in satellite objects, efforts are underway to assess and implement various mitigation strategies. These aim to minimize the impact of space activities and ...

EPFL2024

Insights from an extensive triaxial testing campaign on a shale for comparative site characterization of a deep geological repository

Lyesse Laloui, Alessio Ferrari, Eleonora Crisci

Several boreholes were drilled for site comparison of a deep geological repository (DGR) in Northern Switzerland. The main target of the exploration program was the >100m thick Opalinus Clay, the designated host rock encountered at approximately 450 to 100 ...

Elsevier2024

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Xhemsi Malja

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Design of Customized Mouthguards with Superior Protection Using Digital-Based Technologies and Impact Tests

Dominique Pioletti, Naser Nasrollahzadeh Mamaghani, Martin Broome

Background In contact sports, an impact on the jaw can generate destructive stress on the tooth-bone system. Mouthguards can be beneficial in reducing the injury risk by changing the dynamics of the trauma. The material properties of mouthguards and their ...

Springer2024

Multimaterial Volumetric Printing of Silica-Based Glasses

Christophe Moser, Damien Claude-Marie Loterie, Paul Delrot, Antoine Vincent Boniface, Jorge Andres Madrid Wolff

Silicate glasses have played a major role as structural and functional materials in human civilization since ancient Egypt. Despite their widespread use and importance in modern society, silica glasses with complex geometries are only fabricated in automat ...

Wiley2024

Modeling friction and wear using an adaptive discrete-continuum coupling

Manon Eugénie Voisin--Leprince

When two objects slide against each other, wear and friction occur at their interface. The accumulation of wear forms what is commonly referred to as a ``third-body''. Understanding third-body evolution has significant applications in industry, where contr ...

EPFL2024

Instabilities in Elastic and Magneto-Elastic Beams and Shells: from Shell Buckling to the Design of a Programmable Braille Reader

Arefeh Abbasi

In this thesis, we conduct a comprehensive investigation into structural instabilities of both elastic and magneto-elastic beams and shells, resulting in a creative proposal to design a programmable braille reader. Methodologically, we combine numerical si ...

EPFL2024

Localized Ionic Reinforcement of Double Network Granular Hydrogels

Esther Amstad, Alexandra Thoma

Nature produces soft materials with fascinating combinations of mechanical properties. For example, the mussel byssus embodies a combination of stiffness and toughness, a feature that is unmatched by synthetic hydrogels. Key to enabling these excellent mec ...

Wiley-V C H Verlag Gmbh2024

Ion Spectroscopy Reveals Structural Difference for Proteins Microhydrated by Retention and Condensation of Water

Oleg Boyarkine, Andrei Zviagin

Protein ubiquitin in its +7 charge state microhydrated by 5 and 10 water molecules has been interrogated in the gas phase by cold ion UV/IR spectroscopy. The complexes were formed either by condensing water onto the unfolded bare proteins in a temperature- ...

Amer Chemical Soc2024

Customized modular multi-material mouthguard and method of making the same

Dominique Pioletti, Naser Nasrollahzadeh Mamaghani, Martin Broome

There is described a mouthguard comprising an externally exposed impact protective region defined by a first material property and configured to cover a front tooth, an internally exposed occlusional cushioning region defined by a second material property ...

2024