Publications related to 3D Printing of Polymers with Hierarchical Continuous Porosity

Related publications (30)

Optimizing Atomic Layer Deposition Processes with Nanowire-Assisted TEM Analysis

Atomic layer deposition (ALD) is one of the premier methods to synthesize ultra-thin materials on complex surfaces. The technique allows for precise control of the thickness down to single atomic layers, while at the same time providing uniform coverage ev ...

Wiley2024

Piezoelectric and elastic properties of Al0.60Sc0.40N thin films deposited on patterned metal electrodes

Federico Peretti, Luis Guillermo Villanueva Torrijo, Silvan Stettler, Marco Liffredo, Nan Xu

Sc-doped aluminum nitride (AlScN) allows for piezoelectric devices with large electromechanical coupling and the benefits increase with larger Sc doping in the film. However, with a larger Sc concentration, the process window narrows, and it is necessary t ...

2024

Large-Scale Hollow-Core 3D Printing: Variable Cross-Section and Printing Features for Lightweight Plastic Elements

Marianthi Eririni Kladeftira

Hollow-core 3D printing (HC3DP) proposes a new method for the production of lightweight, material-efficient thermoplastic 3D printed elements. This new fabrication approach promises material savings of 50-80%, while increasing the extrusion rate significan ...

Mary Ann Liebert, Inc2024

Plasmoid drift and first wall heat deposition during ITER H-mode dual-SPIs in JOREK simulations

Mengdi Kong

The heat flux mitigation during the thermal quench (TQ) by the shattered pellet injection (SPI) is one of the major elements of disruption mitigation strategy for ITER. It's efficiency greatly depends on the SPI and the target plasma parameters, and is ult ...

IOP Publishing Ltd2024

Near-Room-Temperature Detection of Aromatic Compounds with Inkjet-Printed Plasticized Polymer Composites

Jürgen Brugger, Thomas Maeder, Mohammadmahdi Kiaee

Chemiresistive gas sensors composed of a thermoplastic polymer matrix and conductive fillers offer various advantages for detecting volatile organic compounds (VOCs), including low power consumption due to near-room-temperature operation, high sensitivity, ...

Amer Chemical Soc2024

Influence of Si3N4 fillers and pyrolysis profile on the microstructure of additively manufactured silicon carbonitride ceramics derived from polyvinylsilazane

Alper Balkan

In this work, various methods were used to improve the printability of a photocurable polyvinylsilazane resin filled with silicon nitride particles for digital light processing. The developed resin was used as a preceramic polymer for polymer-to-ceramic co ...

Taylor & Francis Ltd2024

Towards Scalable Electronics: Synthetic 2D Materials for Large-Area 2D Circuit Integration

Zhenyu Wang

In the past decades, a significant increase of the transistor density on a chip has led to exponential growth in computational power driven by Moore's law. To overcome the bottleneck of traditional von-Neumann architecture in computational efficiency, effo ...

EPFL2024

Additively manufactured stretchable zipping electrostatic actuators

Giulio Grasso

The use of soft and stretchable materials allows the development of adaptive robotic systems and human-machine interfaces that are more natural and comfortable to interact with. One of the application fields that benefits the most from these compliant mate ...

EPFL2024

Influence of Ventilation on Formation and Growth of 1-20 nm Particles via Ozone-Human Chemistry

Dusan Licina, Shen Yang, Marouane Merizak, Meixia Zhang

Ozone reaction with human surfaces is an important source of ultrafine particles indoors. However, 1-20 nm particles generated from ozone-human chemistry, which mark the first step of particle formation and growth, remain understudied. Ventilation and indo ...

Amer Chemical Soc2024

Multimaterial Volumetric Printing of Silica-Based Glasses

Christophe Moser, Damien Claude-Marie Loterie, Paul Delrot, Antoine Vincent Boniface, Jorge Andres Madrid Wolff

Silicate glasses have played a major role as structural and functional materials in human civilization since ancient Egypt. Despite their widespread use and importance in modern society, silica glasses with complex geometries are only fabricated in automat ...

Wiley2024

Font Side Solutions for c-Si Solar Cells with High-Temperature Passivating Contacts

Ezgi Genç

In this work, we studied the potential of using thin films deposited by plasma-enhanced chemical vapor deposition (PECVD) for two main purposes: introducing an n-type passivating contact at the front of a TOPCon solar cell, or simplifying the fabrication o ...

EPFL2024

3D Printing of Customizable Transient Bioelectronics and Sensors

Danick Briand, Nicolas Francis Fumeaux

Transient electronics have emerged as a new category of devices that can degrade after their functional lifetime, offering tremendous potential as disposable sensors, actuators, wearables, and implants. Additive manufacturing methods represent a promising ...

2024

Carbon based printed electrodes for DEAs: study of pad, inkjet, and stencil printing

Yves Perriard, Yoan René Cyrille Civet, Thomas Guillaume Martinez, Stefania Maria Aliki Konstantinidi, Armando Matthieu Walter, Simon Holzer

Dielectric elastomer actuators (DEAs) have raised interest due to their remarkable capabilities in various applications, such as soft robotics, haptic feedback systems, and biomedical devices. To harness the full potential of DEAs, the choice of the electr ...

Society of Photo-Optical Instrumentation Engineers (SPIE)2024

Additive Manufacturing of Bioinspired Mineral-Based Composites

Ran Zhao

Biominerals are used by natural organisms for example as structural supports and optical sensors. They are produced from a limited number of elements and under ambient conditions. Nevertheless, they often possess excellent mechanical properties and sometim ...

EPFL2024

Spinel Protective Coatings for Solid Oxide Cell (SOC) Interconnects (ICs)

Samaneh Daviran

Abstract The degradation of metal interconnects (ICs) in Solid Oxide Cells (SOCs) primarily results from chromium (Cr) oxide scale growth on stainless-steel substrates, causing ohmic loss and air-side electrode poisoning by Cr. This thesis addresses these ...

EPFL2024

Control of intermetallics in the interface in directed energy deposition of titanium on stainless steel 316L

Di Cui

Application of a single metal or alloy is often restricted by its properties from optimal combination of performance and cost. Therefore, there is a vast need of joining dissimilar metals for various applications in biomedical, aerospace, automobile and ma ...

EPFL2023

Additive and digital manufacturing of transient sensors and bioelectronics

Nicolas Francis Fumeaux

Transient electronics have emerged as a promising class of devices, capable of breaking down without harmful side effects to their environment. They have tremendous potential as bioresorbable electronics for temporary applications in the human body, and as ...

EPFL2023

Plasma-Assisted Hybrid Vapour Deposition Technology for Thin Film Fabrication

Caroline Hain

Continuous development of thin film deposition technologies is essential for the fabrication of films that meet the specific requirements of their target applications and working conditions. Therefore, it is necessary to increase the number of accessible a ...

EPFL2023

The physics of 3D printing with light

Christophe Moser

The goal of 3D printing is to realize complex 3D structures by locally adding material in small volume elements called voxels - in contrast to successively subtracting material by etching, milling or machining. This field started with optics-based proposal ...

Nature Portfolio2023

Synthesis of metal oxide-overcoated carbon materials by liquid phase ALD and their applications in catalysis

Farzaneh Talebkeikhah

Coating nano particles and other substrates for efficiency enhancement, protection and obtaining new atomic structures is a widespread research topic in catalysis and material synthesis. Thus far, different approaches of coating, ranging from simplest to s ...

EPFL2023