Publications related to Influence of surface shapes on the mechanical behaviour of friction welded wood bonds

Related publications (31)

Synergistic integration of digital twins and zero energy buildings for climate change mitigation in sustainable smart cities: A systematic review and novel framework

Sustainable smart cities are increasingly turning to innovative technologies, such as Urban Digital Twins (UDTs) and Zero Energy Buildings (ZEBs), which offer transformative opportunities to enhance energy management and reduce environmental impacts. Despi ...

2025

A novel fatigue life prediction methodology based on energy dissipation in viscoelastic materials, synergistic effects of stress level, stress ratio, and temperature

Thomas Keller, Lulu Liu, Abdolvahid Movahedirad

This work introduces a new methodology to predict the fatigue life of viscoelastic materials by considering the creep effect on fatigue behavior under the concurrent effects of stress level, stress ratio, and temperature. The model established based on the ...

2024

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Xhemsi Malja

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Landolf-Giosef-Anastasios Rhode-Barbarigos, Tara Habibi

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

2024

Parametric Reduced Order Model of a Gas Bearings Supported Rotor

Jürg Alexander Schiffmann, Fabio Nobile, Dimitri Maurice Goutaudier

Gas bearings use pressurized gas as a lubricant to support and guide rotating machinery. These bearings have a number of advantages over traditional lubricated bearings, including higher efficiency in a variety of applications and reduced maintenance requi ...

2023

Modeling friction and wear using an adaptive discrete-continuum coupling

Manon Eugénie Voisin--Leprince

When two objects slide against each other, wear and friction occur at their interface. The accumulation of wear forms what is commonly referred to as a ``third-body''. Understanding third-body evolution has significant applications in industry, where contr ...

EPFL2024

Insights from an extensive triaxial testing campaign on a shale for comparative site characterization of a deep geological repository

Lyesse Laloui, Alessio Ferrari, Eleonora Crisci

Several boreholes were drilled for site comparison of a deep geological repository (DGR) in Northern Switzerland. The main target of the exploration program was the >100m thick Opalinus Clay, the designated host rock encountered at approximately 450 to 100 ...

Elsevier2024

Exploring the potential of the critical shear crack theory for reinforced and post-tensioned glass beams: Initial analysis and experiments

Alain Nussbaumer, Pieter Christian Louter, Jagoda Cupac

In the evolution of structural glass beam elements, the requirements for post-fracture load bearing capacity and safe failure behaviour have led to the development of reinforced and post-tensioned beams. Maximum bending capacity in the post-fracture state ...

2023

Lattice Green's function method for Atomistic/Continuum coupling

Ankit Gupta

Metal plasticity is an inherently multiscale phenomenon due to the complex long-range field of atomistic dislocations that are the primary mechanism for plastic deformation in metals. Atomistic/Continuum (A/C) coupling methods are computationally efficient ...

EPFL2023

Graph neural networks for dynamic modeling of roller bearings

Olga Fink, Vinay Sharma

Machine learning has paved the way for the real-time monitoring of complex infrastructure and industrial systems. However, purely data-driven methods have not been able to learn the underlying dynamics and generalize them to operating conditions that have ...

PHM Society2023

Mechanics, Modeling, and Upscaling of Biocemented Soils: A Review of Breakthroughs and Challenges

Lyesse Laloui, Dimitrios Terzis, Ray Harran

Biogeotechnical research has inspired revolutionary ideas to claim the status of a distinctive branch of geotechnical engineering. Most notably, underground carbonate mineralization, most commonly referred to as microbially induced carbonate precipitation ...

ASCE-AMER SOC CIVIL ENGINEERS2023

Parametric Reduced Order Model of a Gas Bearings Supported Rotor

Fabio Nobile, Jürg Alexander Schiffmann, Dimitri Maurice Goutaudier

Gas bearings use pressurized gas as a lubricant to support and guide rotating machinery. These bearings have a number of advantages over traditional lubricated bearings, including higher efficiency in a variety of applications and reduced maintenance requi ...

Amer Soc Mechanical Engineers2023

Robust Design of Herringbone Grooved Journal Bearings using Multi-Objective Optimization with Artificial Neural Networks

Jürg Alexander Schiffmann, Soheyl Massoudi

Herringbone grooved journal bearings (HGJBs) are widely used in micro-turbocompressor applications due to their high load-carrying capacity, low friction, and oil-free solution. However, the performance of these bearings is sensitive to manufacturing devia ...

2023

Robust Design of Herringbone Grooved Journal Bearings using Multi-Objective Optimization with Artificial Neural Networks

Jürg Alexander Schiffmann, Soheyl Massoudi

Herringbone grooved journal bearings (HGJBs) are widely used in micro-turbocompressor applications due to their high load-carrying capacity, low friction, and oil-free solution. However, the performance of these bearings is sensitive to manufacturing devia ...

Amer Soc Mechanical Engineers2023

Room-temperature strength of the interfacial bond between silica inclusions and iron

Andreas Mortensen, Alejandra Inés Slagter, David Hernandez Escobar

The strength of the interface between iron (Fe) and individual spherical silica (SiO2) inclusions of 5 +/- 1 mu m diameter is measured by means of in-situ micro-cantilever bending tests conducted under displacement control within a scanning electron micros ...

Pergamon-Elsevier Science Ltd2023

On the slip burst amplitude cutoff in dislocation-rich microcrystals

Andreas Mortensen, Luciano Borasi

The plastic deformation of small-scale face-centered cubic metals exhibits intermittent slip burst events that appear on stress-strain curves as sudden strain jumps and/or load drops. These events are generally attributed to the avalanche-like cooperative ...

Pergamon-Elsevier Science Ltd2023

Microscopic Digital Image Correlation Analysis of Strain Distributions in Stainless Steel 316L Induced by Multiaxial Cyclic Loading

Elif Cansu Kursun

Fatigue damage in materials results in localized strain at the microstructural level. In many engineering components of the cooling circuits of nuclear power plants, where austenitic steels are used, the material experiences multiaxial cyclic loading, eith ...

EPFL2023

BamX: Rethinking Deployability in Architecture through Weaving

Mark Pauly, Stefana Parascho, Tian Chen, Yingying Ren, Seiichi Eduardo Suzuki Erazo

Deployable gridshells are a class of planar-to-spatial structures that achievea 3D curved geometry by inducing bending on a flat grid of elastic beams. However, theslender nature of these beams often conflicts with the structure’s load-bearing capacity.To ...

De Gruyter2023

A 2000-year temperature reconstruction on the East Antarctic plateau from argon-nitrogen and water stable isotopes in the Aurora Basin North ice core

Jérôme Chappellaz

The temperature of the Earth is one of the most important climate parameters. Proxy records of past climate changes, in particular temperature, represent a fundamental tool for exploring internal climate processes and natural climate forcings. Despite the ...

COPERNICUS GESELLSCHAFT MBH2023

Interactive design with optimum matchmaking of reused structural elements – a software implementation

Corentin Jean Dominique Fivet, Jan Friedrich Georg Brütting, Jonas Warmuth

Structural systems are a significant contributor to buildings’ embodied carbon and reusing structural elements in new load-bearing applications is one strategy to reduce this impact. However, integrating this approach into existing design workflows without ...

International Association for Shell and Spatial Structures (IASS)2023