Photo-polymerized epoxy primer for adhesion improvement at thermoplastics/metallic wires interfaces

About
Privacy
Disclaimer

Graph Chatbot

Related publications (31)

Cyclic Behaviour of Unidirectional Hybrid Interlayer Glass/Carbon and Carbon/Carbon Composites

Anastasios Vassilopoulos, José Manuel de Sena Cruz

The lack of ductility is a major drawback of fibre reinforced polymer (FRP) materials. As it is known, these materials are stiff and strong, but brittle with little or no warning before final failure. In the last decades, some solutions have been proposed ...

SPRINGER-VERLAG SINGAPORE PTE LTD2022

Hydro-processing of biomass using novel metal-organic framework (MOF)/polymer composite catalysts

Vikram Vinayak Karve

Generating value, in the form of functional chemicals, from biomass is a critical need of today. It is expected that replacing petroleum with biomass as the source of many commodity and fine chemicals can lead the transition away from a fossil-fuel based e ...

EPFL2022

Enhancement of Pressure-Sensitive Adhesive by CO2 Laser Treatment

Dario Floreano, Jianhang Yang, Jun Shintake, Vivek Ramachandran, Yegor Piskarev, Michael Dickey

Pressure-sensitive adhesives (PSAs) are polymeric films that can be adhered to and detached from surfaces without leaving residue. Researchers are looking to enhance the bond strength between PSAs and different substrates. It can be achieved by tuning PSA' ...

2022

Transient Elastomers with High Dielectric Permittivity for Actuators, Sensors, and Beyond

Holger Frauenrath, Yauhen Sheima

Dielectric elastomers (DEs) are key materials in actuators, sensors, energy harvesters, and stretchable electronics. These devices find applications in important emerging fields such as personalized medicine, renewable energy, and soft robotics. However, e ...

AMER CHEMICAL SOC2022

Some Results of the EU Project FASTGRID

Manuel Bauer

The EU FASTGRID project aimed at improving the REBCO conductor in order to enhance its economical attractiveness for the Superconducting Fault Current Limiter (SFCL). Two approaches were simultaneously investigated: i) the reduction of the tape length thro ...

IEEE Institute of Electrical and Electronics Engineers2022

Semiaromatic polyamides with enhanced charge carrier mobility

John Christopher Plummer, Holger Frauenrath, Nicolas Candau

The control of local order in polymer semiconductors using non-covalent interactions may be used to engineer materials with interesting combinations of mechanical and optoelectronic properties. To investigate the possibility of preparing n-type polymer sem ...

ROYAL SOC CHEMISTRY2021

From vesicles to materials: bioinspired strategies for fabricating hierarchically structured soft matter

Esther Amstad

Certain organisms including species of mollusks, polychaetes, onychophorans and arthropods produce exceptional polymeric materials outside their bodies under ambient conditions using concentrated fluid protein precursors. While much is understood about the ...

ROYAL SOC2021

Reversible and Broad-Range Oxygen Sensing Based on Purely Organic Long-Lived Photoemitters

Esther Amstad, Efe Armagan, René M. Rossi

The detection of oxygen (O-2) by optical sensors is of growing importance, for example, in biology, life science, environmental science, and aerodynamics, where the composition of gases is crucial for many applications. Purely organic optical O-2 sensors a ...

2021

In-situ laser sintering for the fabrication of fully 3D printed electronics composed of elastomeric materials

Danick Briand, Sébastien Lani, Olivier Rémy Henry Chandran, Rubaiyet Iftekharul Haque, Ryan Mitchell van Dommelen

In-situ laser sintering can be used to locally sinter conductive inks in an uninterrupted process, enabling the embedding of printed electronics within 3D printed structures. In this work we apply a laser sintering method to create highly conductive silver ...

2021

Mechanical reinforcement and memory effect of strain-induced soft segment crystals in thermoplastic polyurethane-urea elastomers

Nicolas Candau, Adrien Julien Demongeot, Oguzhan Oguz

An amorphous poly(urethane-urea) copolymer composed of 70 wt% poly(ethylene oxide) (PEO) soft segments (SS) (Mw = 2000 g mol−1) and 30 wt% cycloaliphatic hard segments (HS) was subjected to in-situ X-Rays during tensile deformation. Mechanical hardening at ...

2021

Functionalized Fiber Reinforced Composites via Thermally Drawn Multifunctional Fiber Sensors

Véronique Michaud, Dang Tùng Nguyen, Fabien Sorin, Stella Andréa Françoise Laperrousaz, Baris Çaglar, William Nicolas Duncan Esposito

Monitoring fiber reinforced polymer composites (FRPC) during their production and operation is becoming crucial to track the performance of the final parts and optimize the overall life cycle. The challenges associated with integrating multifunctional sens ...

Wiley2021

Page 2 of 2