Home

Publication

Mixed-mode fracture of adhesively-bonded pultruded composite lap joints

About
Privacy
Disclaimer

Graph Chatbot

Related publications (36)

Page 2 of 2

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Diego Hernández Fraile

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

EPFL2024

Experimental investigation of dowel action in reinforcing bars using refined measurements

Aurelio Muttoni, Marko Pejatovic

In typical reinforced concrete design, reinforcement is designed to carry axial forces, but it can also resist transversal forces by dowel action. This is usually neglected for simplicity's sake in the design phase, but it can be accounted for either expli ...

Ernst & Sohn2024

Proposed residual stress model for hot‐rolled wide flange steel cross sections

Dimitrios Lignos, Albano António De Abreu E Presa De Castro E Sousa, Andronikos Skiadopoulos

Residual stresses in hot-rolled wide flange steel cross sections may lead to premature yielding, accelerated corrosion and brittle fracture of steel members. The above phenomena lead to a loss of a steel member's stiffness and resistance under mechanical l ...

Ernst & Sohn2023

Influence of fiber orientation on the high cycle tensile fatigue resistance of Ultra-High Performance Fiber Reinforced Cementitious

Eugen Brühwiler, Alain Nussbaumer, Jian Zhan

This paper quantitatively studies the influence of fiber orientation on the high cycle tensile fatigue resistance of ultra-high performance fiber reinforced cementitious composites (UHPFRC) within and beyond elastic domain. Eight tensile fatigue tests and ...

2024

Propagation of planar three-dimensional buoyant hydraulic fractures

Andreas Möri

Hydraulic fractures are driven by an internal fluid pressure exceeding the minimum compressive stress, propagating in a direction perpendicular to the latter. This class of tensile fractures has gained interest over the last fifty years due to the developm ...

EPFL2023

Instabilities in Elastic and Magneto-Elastic Beams and Shells: from Shell Buckling to the Design of a Programmable Braille Reader

Arefeh Abbasi

In this thesis, we conduct a comprehensive investigation into structural instabilities of both elastic and magneto-elastic beams and shells, resulting in a creative proposal to design a programmable braille reader. Methodologically, we combine numerical si ...

EPFL2024

Crack tip kinematics reveal the process zone structure in brittle fracture

John Martin Kolinski, Chenzhuo Li, Xinyue Wei

When brittle hydrogels fail, several mechanisms conspire to alter the state of stress near the tip of a crack, and it is challenging to identify which mechanism is dominant. In the fracture of brittle solids, a sufficient far-field stress results in the co ...

PERGAMON-ELSEVIER SCIENCE LTD2023

Using video detection of snow surface movements to estimate weak layer crack propagation speeds

Johan Alexandre Philippe Gaume, Bertil Trottet

Dry-snow slab avalanches release due to crack propagation in a weak snow layer under a cohesive snow slab. Crack propagation speeds can provide insights into the potential size of avalanches and inform fracture and avalanche release models. Despite their i ...

CAMBRIDGE UNIV PRESS2023

Single-Well Pore Pressure Preconditioning for Enhanced Geothermal System Stimulation

Marie Estelle Solange Violay, Barnaby Padraig Fryer, Mathias Alexandre David Lebihain

The stress state is an important parameter in terms of both earthquake nucleation and rupture. Here, a new stimulation technique is proposed for Enhanced Geothermal Systems (EGSs), which have previously been burdened with a number of high-profile incidence ...

2023

Experimental investigation of two-dimensional Mode-II delamination in composite laminates

Thomas Keller, Anastasios Vassilopoulos, Congzhe Wang

The two-dimensional (2D) delamination growth in composite laminates under the Mode-II fracture condition was experimentally investigated using a novel set-up. Circular plate specimens with a centrally embedded pre-crack of two sizes were semi-clamped along ...

2023

Deformation response of highly stretchable and ductile graphene kirigami under uniaxial and biaxial tension

Ye Wei, Yao Chen

Kirigami, the ancient technique of paper cutting, has been successfully applied to enhance the stretchability and ductility of nanoscale graphene. However, existing experimentally realized graphene kirigami (GK) are created by introducing parallel cuts, ex ...

Amer Physical Soc2023

Three-dimensional hydraulic fracture propagation in homogeneous and heterogeneous media

Carlo Peruzzo

Hydraulic fractures are tensile fractures that occur in solid materials due to the natural intrusion or anthropogenic injection of a viscous fluid into a fracture channel. The deliberate creation of hydraulic fractures is part of an industrial technology h ...

EPFL2023

Novel multi-crack damage approach for pultruded fiber-polymer web-flange junctions

Thomas Keller

This paper aims to propose a novel approach to assess the multi-crack behavior of layered fiber-polymer composites. The Compliance and R-curves generated from this novel approach were useful to understand the multiple delamination process, enabling to eval ...

Elsevier Sci Ltd2023

Three-dimensional buoyant hydraulic fractures: finite volume release

Brice Tanguy Alphonse Lecampion, Andreas Möri

In impermeable media, a hydraulic fracture can continue to expand even without additional fluid injection if its volume exceeds the limiting volume of a hydrostatically loaded radial fracture. This limit depends on the mechanical properties of the surround ...

Cambridge University Press2023

Friction and fracture: richness and complexity in dynamic rupture

Thibault Didier Roch

Understanding how things break and slide is of paramount importance to describe the dynamics of a broad range of physical systems. This includes day-to-day problems such as the breaking of a glass of wine or the sliding of skis on snow, but also engineerin ...

EPFL2023

Reliability analysis and partial safety format calibration considering the characteristics of the resistance of reinforced concrete structures

Qianhui Yu

Every engineering calculation is an approximation of reality, with inevitable uncertainties involved. This fact implies that a reliability verification accounting for the uncertainties is a necessary step in the design and assessment of structures. Nowaday ...

EPFL2023