Modelling fatigue crack propagation of a cracked metallic member reinforced by composite patches

Chat with Graph Search

Ask any question about EPFL courses, lectures, exercises, research, news, etc. or try the example questions below.

DISCLAIMER: The Graph Chatbot is not programmed to provide explicit or categorical answers to your questions. Rather, it transforms your questions into API requests that are distributed across the various IT services officially administered by EPFL. Its purpose is solely to collect and recommend relevant references to content that you can explore to help you answer your questions.

To explore the governing mechanism underlying the tensile fatigue behavior of Ultra-high Performance Fiber Reinforced Cementitious Composites (UHPFRC), this study tested eight specimens using four advanced non-destructive measurement techniques. First, mag ...

Fractures are diverse geological features. Despite extensive research on their varied geometries and growth mechanisms, there has been relatively little focus on how acid-rock interactions, such as reactive transport and precipitation, influence crack grow ...

Modeling the 3D internal crack under compression entails complex fracture mechanics (mode I-II-III fracture), resulting in substantial computational costs and challenges in characterizing fracture morphology characterization for Phase Field Method (PFM) si ...

Fiber-polymer composites consist of a polymer matrix and reinforcing fibers made of various materials. These composites exhibit exceptional properties, such as a high strength-to-weight ratio and excellent corrosion resistance, which has led to their incre ...

This article investigates the effects of voids, joint geometry, and test conditions on the quasi-static Mode I fracture performance of thick adhesive Double Cantilever Beam (DCB) joints such as those prevailing in wind industry and shipbuilding. The specim ...

When two objects slide against each other, wear and friction occur at their interface. The accumulation of wear forms what is commonly referred to as a ``third-body''. Understanding third-body evolution has significant applications in industry, where contr ...

Wind turbine rotor blades are usually fabricated using composite materials and epoxy adhesive to bond the elements together. Due to their large size, the thickness of the adhesive layer varies from 1 to up to 30 mm depending on the position. The failure of ...

The tensile deformation of top-down cracks significantly influences pavement delamination. Accurately formulating the stress intensity factor (SIF) is crucial for assessing the stress/strain near crack tips. In the present study, a robust data mining metho ...

Ultra-high performance fiber reinforced cementitious composite (UHPFRC) is a modern class of cementitious building materials. Because of its superior mechanical properties and durability, it is increasingly used globally to rehabilitate, strengthen and mod ...

Our understanding of quantum materials is commonly based on precise determinations of their electronic spectrum by spectroscopic means, most notably angle-resolved photoemission spectroscopy (ARPES) and scanning tunneling microscopy. Both require atomicall ...

Titanium-based Metal Matrix Composites (MMCs) manufactured by additive manufacturing offer tremendous lightweighting opportunities. However, processing the high reinforcement contents needed to substantially improve elastic modulus while conserving signifi ...

This data package supports the publication 'Complexity of crack front geometry enhances toughness of brittle solids' by Xinyue Wei, Chenzhuo Li, Cían McCarthy, and John M. Kolinski Nature physics (2024) - https://doi.org/10.1038/s41567-024-02435-x DOI: 1 ...

Estimating the stress of reinforcing bars and its variations in service conditions can be useful to determine the reserve capacity of structures or to assess the risk of fatigue in the reinforcement. This paper investigates the use crack width measurements ...

Surface-based inflatables are composed of two thin layers of nearly inextensible sheet material joined together along carefully selected fusing curves. During inflation, pressure forces separate the two sheets to maximize the enclosed volume. The fusing c ...

The construction industry has recently increased the adoption of additive manufacturing (AM, also known as 3D-printing) technologies. This review paper presents the state of the art of ground-based AM systems in construction, focusing comprehensively on de ...

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

Water is ubiquitous within the pore space of rocks and has been shown to affect their physical and mechanical behaviour. Indeed, water can act on the rock strength via mechanical (i.e., reducing the effective stresses) or chemical effects (e.g., mineral di ...

In typical reinforced concrete design, reinforcement is designed to carry axial forces, but it can also resist transversal forces by dowel action. This is usually neglected for simplicity's sake in the design phase, but it can be accounted for either expli ...

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

In impermeable media, a hydraulic fracture can continue to expand even without additional fluid injection if its volume exceeds the limiting volume of a hydrostatically loaded radial fracture. This limit depends on the mechanical properties of the surround ...

Modelling fatigue crack propagation of a cracked metallic member reinforced by composite patches

Chat with Graph Search

Deciphering tensile fatigue behavior of UHPFRC using magnetoscopy, DIC and acoustic emission

Time-Dependent Deformation of Sandstone due to Chemical Corrosion: An Investigation Using the Heterogeneous Grain-Based Phase-Field Method

An adaptive phase field approach to 3D internal crack growth in rocks

Two-dimensional quasi-static delamination in composite laminates under Mode-I and Mode-II conditions

Mode I fracture of thick adhesively bonded GFRP composite joints for wind turbine rotor blades

Modeling friction and wear using an adaptive discrete-continuum coupling

Improved Material Formulations for Thick Adhesive Joints in Wind Turbine Blades

Formulation of stress intensity factor under pure bending condition in multilayer pavements using numerical study and model tree approach

Influence of fiber orientation on the tensile behavior of UHPFRC and reinforced UHPFRC under static and fatigue loadings

Controlling crystal cleavage in focused ion beam shaped specimens for surface spectroscopy

Tensile Properties of Ex-Situ Ti-TiC Metal Matrix Composites Manufactured by Laser Powder Bed Fusion

Dataset for "Complexity of crack front geometry enhances toughness of brittle solids"

Estimation of the bar stress based on crack width measurements in reinforced concrete structures

Computational Homogenization for Inverse Design of Surface-based Inflatables

The rise of aerial additive manufacturing in construction: a review of material advancements

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Water weakening and the compressive brittle strength of carbonates: Influence of fracture toughness and static friction

Experimental investigation of dowel action in reinforcing bars using refined measurements

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Three-dimensional buoyant hydraulic fractures: finite volume release