Publications related to Deciphering tensile fatigue behavior of UHPFRC using magnetoscopy, DIC and acoustic emission

Related publications (25)

Fluid Chemistry Effect on Localized and Ductile Deformation of a Porous Sandstone

Marie Estelle Solange Violay, Gabriel Gérard Dominique Meyer, Francesco Lazari

In geological reservoirs, pore fluid chemistry can affect rock strength by inducing mineral dissolution, precipitation, and alteration, among other processes. Increasing pressure and temperature can shift deformation from localized to ductile, decreasing p ...

2025

Influence of the Horizontal-to-Vertical Compressive Strength of Hollow Clay Bricks on the In-Plane Drift Capacity of Unreinforced Masonry Walls

Katrin Beyer, Savvas Saloustros, Ernesto Andrés Inzunza Araya

The seismic damage of masonry walls is reflected in cracks that tend to start at the head and bed joints and subsequently propagates through the masonry units. In this regard, the horizontal-to-vertical compressive strength ratio of bricks might have the a ...

2025

Time-Dependent Deformation of Sandstone due to Chemical Corrosion: An Investigation Using the Heterogeneous Grain-Based Phase-Field Method

Alexandra Roma Larisa Kushnir

Fractures are diverse geological features. Despite extensive research on their varied geometries and growth mechanisms, there has been relatively little focus on how acid-rock interactions, such as reactive transport and precipitation, influence crack grow ...

SPRINGER WIEN2025

Achieving strength-ductility synergy in AISI 904L superaustenitic alloy through severe plastic deformation and post-deformation annealing

Mohammad Mobasheri

The evolution of microstructure and mechanical properties of AISI 904L stainless steel subjected to high-pressure torsion (HPT) and post-deformation annealing was investigated. A nanocrystalline microstructure with an average grain size of 48 nm was obtain ...

2025

Tensile Properties of Ex-Situ Ti-TiC Metal Matrix Composites Manufactured by Laser Powder Bed Fusion

Roland Logé

Titanium-based Metal Matrix Composites (MMCs) manufactured by additive manufacturing offer tremendous lightweighting opportunities. However, processing the high reinforcement contents needed to substantially improve elastic modulus while conserving signifi ...

2024

Improved Material Formulations for Thick Adhesive Joints in Wind Turbine Blades

Jialiang Fan

Wind turbine rotor blades are usually fabricated using composite materials and epoxy adhesive to bond the elements together. Due to their large size, the thickness of the adhesive layer varies from 1 to up to 30 mm depending on the position. The failure of ...

EPFL2024

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Diego Hernández Fraile

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

EPFL2024

Experimental and numerical investigation of an additively manufactured sandwich composite bridge deck utilizing gyroid building blocks

Anastasios Vassilopoulos

This work investigates the integration of Additive Manufacturing (AM) techniques with cellular metamaterials integrated into composite sandwich beam systems. The study proposes an approach that combines composite materials for the face sheets with cellular ...

2024

Early detection of structural damage in UHPFRC structures through the combination of acoustic emission and ultrasonic stress wave monitoring

Eugen Brühwiler, Numa Joy Bertola, Thomas Schumacher

Ultra-High-Performance Fiber-Reinforced Cementitious Composite (UHPFRC) offers several advantages compared to concrete, notably due to the strain hardening behavior under tensile actions. Structures made of this composite material are lightweight and highl ...

2024

Highly anisotropic carbon fiber electrodes for DEAs and their dynamic non-monotonic conductive properties

Yves Perriard, Stefania Maria Aliki Konstantinidi

A common method for creating compliant electrodes for dielectric elastomer actuators (DEAs) and soft sensors is to incorporate electrically conductive carbon particles into a polymer matrix. However, using unidirectional aligned carbon fibers instead not o ...

Society of Photo-Optical Instrumentation Engineers (SPIE)2024

Numerical investigation of two-dimensional Mode-II delamination in composite laminates

Thomas Keller, Anastasios Vassilopoulos, Congzhe Wang

Existing standards for delamination tests on composite materials typically employ one-dimensional (1D) beam specimens. However, such specimens may not represent real delamination scenarios in composite structures, where cracks tend to propagate in two dime ...

Elsevier Sci Ltd2024

Refractive Index Matched (RIM) PIV in Free Surface Flows of Particle-Laden Yield Stress Fluids

Christophe Ancey, Yanan Chen

Flow of lava, avalanches, mudslides, and many geophysical and planetary flow systems are examples of free-surface flows of Yield Stress Fluids (YSFs). This category of fluids is known for its dual behavior below- and above a yielding threshold for the appl ...

2024

The rise of aerial additive manufacturing in construction: a review of material advancements

Mirko Kovac, Yusuf Furkan Kaya

The construction industry has recently increased the adoption of additive manufacturing (AM, also known as 3D-printing) technologies. This review paper presents the state of the art of ground-based AM systems in construction, focusing comprehensively on de ...

2024

Uniaxial Cyclic and Tensile Tests on Structural Metallic Materials

Dimitrios Lignos, Albano António De Abreu E Presa De Castro E Sousa, Selimcan Ozden

Experimental data is imperative to characterize the behavior of materials used in structural analysis models. The aim of this data paper is to establish a database of material-scale uniaxial experiments, primarily conducted at EPFL, to assist with simulati ...

ASCE-AMER SOC CIVIL ENGINEERS2023

Influence of Fiber Orientation on the Elastic Limit Tensile Stress of UHPFRC

Eugen Brühwiler, Emmanuel Denarié, Jian Zhan

The elastic limit tensile stress of UHPFRC is governed by contributions of the cementitious matrix and the fibrous skeleton. This paper finds that fiber orientation has significant influence on the matrix tensile strength of UHPFRC, while this is not consi ...

2023

Pultruded carbon fibre reinforced polymer strips produced with a novel bio-based thermoset polyester for structural strengthening

Mateus De Assunção Hofmann

This paper presents the development and industrial manufacturing of a pultruded high-performance carbon fibre (CF) reinforced polymer (CFRP) composite strip using a bio-based unsaturated polyester (UP) resin containing more than 50% of its weight derived f ...

ELSEVIER SCI LTD2023

Polydimethylsiloxane based soft polymer optical fibers: From the processing-property relationship to pressure sensing applications

Fabien Sorin, Khushdeep Sharma

Polydimethylsiloxane (PDMS) based soft polymer optical fibers (POFs) have recently demonstrated their intriguing potential for different sensing applications like strain or temperature sensing. Recent studies have elaborated on the sensing capability of PD ...

2023

Enhancing Robustness of Adhesive Hydrogels through PEG-NHS Incorporation

Dominique Pioletti, François Gorostidi, Yanheng Guo, Theofanis Stampoultzis, Vijay Kumar Rana, Ece Mailand

Tissue wounds are a significant challenge for the healthcare system, affecting millions globally. Current methods like suturing and stapling have limitations as they inadequately cover the wound, fail to prevent fluid leakage, and increase the risk of infe ...

Amer Chemical Soc2023

A Three-Dimensional Engineered Cardiac In Vitro Model: Controlled Alignment of Cardiomyocytes in 3D Microphysiological Systems

Philippe Renaud, Fatemeh Navaee

Cardiomyocyte alignment in myocardium tissue plays a significant role in the physiological, electrical, and mechanical functions of the myocardium. It remains, however, difficult to align cardiac cells in a 3D in vitro heart model. This paper proposes a si ...

MDPI2023

The challenges of quasi-static and fatigue experiments of structural adhesives

Anastasios Vassilopoulos

This paper presents the results of an experimental campaign designed specifically to investigate unexpected and unwanted failures observed during the quasi-static and fatigue tensile loading of structural adhesives. Simple finite element models were also d ...

ELSEVIER SCI LTD2022