Publications related to Compressive Membrane Action Effects on Punching Strength of Flat RC Slabs

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

EPFL2024

Contributions to rebar-to-concrete interaction and its structural implications for design and monitoring applications

Enrique Corres Sojo

Bond between reinforcing bars and concrete has been the focus of extensive research over the last century. This is well-justified as the functioning of reinforced concrete intimately depends on the interaction between rebar and concrete, as for example cra ...

EPFL2024

Mesh-based topology, shape and sizing optimization of ribbed plates

In this paper, we present a new parameterization and optimization procedure for minimizing the weight of ribbed plates. The primary goal is to reduce embodied CO2 in concrete floors as part of the effort to diminish the carbon footprint of the construction ...

Springer2024

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Xhemsi Malja

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Estimation of the bar stress based on crack width measurements in reinforced concrete structures

Aurelio Muttoni, Enrique Corres Sojo

Estimating the stress of reinforcing bars and its variations in service conditions can be useful to determine the reserve capacity of structures or to assess the risk of fatigue in the reinforcement. This paper investigates the use crack width measurements ...

Ernst & Sohn2024

Structural component reuse of precast and cast-in-place reinforced concrete in architecture since the late 1960s in Europe

Célia Marine Küpfer, Corentin Jean Dominique Fivet

The reuse of concrete pieces salvaged from structures undergoing transformation or demolition into new architectural projects has gained a sudden and visible interest over the past five years. However, the practice of reusing concrete pieces in new structu ...

vdf Hochschulverlag AG2024

Experimental and analytical investigation of shear-reinforced concrete and dowel action

Marko Pejatovic

Codes of practice can be overly conservative, particularly for the shear resistance of reinforced concrete beams with shear reinforcement when large loads act close to supports. This thesis addresses the topic by proposing a refined design approach based o ...

EPFL2024

Experimental investigation of dowel action in reinforcing bars using refined measurements

Aurelio Muttoni, Marko Pejatovic

In typical reinforced concrete design, reinforcement is designed to carry axial forces, but it can also resist transversal forces by dowel action. This is usually neglected for simplicity's sake in the design phase, but it can be accounted for either expli ...

Ernst & Sohn2024

Decarbonization potential of steel fibre-reinforced limestone calcined clay cement concrete one-way slabs

Hisham Tarek Mohamed Hafez

This study deals with a comparison of the environmental performance of one-way slabs utilizing steel fibrereinforced limestone calcined clay cement (LC3) concrete with the control case of Ordinary Portland cement concrete. The experimental program constitu ...

Elsevier Sci Ltd2024

FLO:RE – A new floor system made of reused reinforced concrete and steel elements

Maléna Bastien Masse, Numa Joy Bertola, Célia Marine Küpfer, Corentin Jean Dominique Fivet

Carefully extracting reinforced concrete (RC) elements from soon-to-be demolished structures and reusing them as load-bearing components is an emerging circular low-carbon alternative to building new structures. As floor construction typically accounts for ...

IABSE2024

Additively manufactured steel reinforcement for small scale reinforced concrete modeling: Tensile and bond behavior

Christian Leinenbach, Rafal Wróbel

Small scale (1:30-1:40) Reinforced Concrete is useful for centrifuge testing. However, manufacturing the reinforcing cages by hand at this scale is practically difficult. This paper suggests that small scale reinforcement can be manufactured using a metal ...

Elsevier Sci Ltd2024

Experimental testing and structural analysis of composite tile – reinforced concrete domes

Savvas Saloustros

Conventional formworks for concrete curved shells either are expensive, complex and wasteful or have formal restrictions. Using tile vaults (also known as timbrel, Guastavino, thin-tile or Catalan vaults) as stay-in-place formwork for concrete shells could ...

2023

Environmental and Life-Cycle Cost Evaluation of a Composite Timber-UHPFRC Bridge

Eugen Brühwiler, Numa Joy Bertola

Ultra-High-Performance Fibre Reinforced Cementitious Composite (UHPFRC) has recently been used to design lightweight structures and strengthen existing ones, with more than 300 applications in Switzerland. Several composite timber-UHPFRC bridges have been ...

2023

Design of New Low-Carbon Floor Systems by Reusing Cut Cast-in-Place Concrete Pieces

Numa Joy Bertola, Célia Marine Küpfer, Corentin Jean Dominique Fivet

As floors typically account for the largest share of a building embodied carbon footprint, new strategies to build low-carbon floors must be developed and implemented. Among these strategies, the reuse of existing components is a promising circular approac ...

Novus Press2023

A Discussion on the Reliability of prEN1992-1-1:2021 Shear Strength Provisions for Fibre Reinforced Concrete Members Without Shear Reinforcement

Miguel Fernández Ruiz

The Eurocode 2 for the design of concrete structures (EN1992-1-1:2004) is undergoing a revision that will lead to the publication of the second generation of this code to be used across all CEN member countries. Therefore, the impact of the code will reach ...

SPRINGER INTERNATIONAL PUBLISHING AG2023

Panorama of approaches to reuse concrete pieces: identification and critical comparison

Célia Marine Küpfer, Corentin Jean Dominique Fivet

Practices that reuse concrete pieces in new building or infrastructure projects are currently diversifying as concrete reuse gains more and more relevance for sustainability. The present research provides a yet missing identification of the main approaches ...

IOP Publishing2023

Punching of edge columns with and without shear reinforcement: an experimental investigation

Aurelio Muttoni, Diego Hernández Fraile, Andri Setiawan, Júlia Borges Dos Santos

Most research efforts in the past related to the punching resistance of reinforced concrete slabs have concentrated on the response of internal slab-column connections, where significant advances in the state-of-the-art have been performed. Other than inte ...

Fédération Internationale du Béton (fib)2022

Characterization of shear deformations in reinforced concrete members without shear reinforcement

Aurelio Muttoni, Miguel Fernández Ruiz, Raffaele Cantone, Andri Setiawan

The load-carrying capacity of many reinforced concrete structures is governed by shear failures, occurring before reaching the flexural capacity of the member. For redundant systems, such as slabs subjected to concentrated loads, local shear failures (typi ...

2022

A new perspective on the punching resistance of edge columns with and without shear reinforcement applying refined measurement techniques

Aurelio Muttoni, Diego Hernández Fraile

Despite edge columns being instrumental components of flat slabs, most punching research has focused on internal connections. Several particularities of edge columns, such as load eccentricity and moment transfer, require additional experimental investigat ...

Fédération Internationale du Béton (fib)2022

Deformation capacity evaluation for flat slab seismic design

Aurelio Muttoni, António Manuel Pinho Ramos, Lorenzo Martinelli, Andri Setiawan

In flat-slab frames, which are typically designed as secondary seismic structures, the shear failure of the slab around the column (punching failure) is typically the governing failure mode which limits the deformation capacity and can potentially lead to ...

SPRINGER2022