Publications related to Quench-Induced Stresses in AA2618 Forgings for Impellers: A Multiphysics and Multiscale Problem

Related publications (34)

Cyclic loading of WC-Ni by FEM with a realistic 3D morphology

Daniele Mari, Lucas Eric Jacques Degeneve

A Finite Element Model produced from a real WC-10wt.%Co sample is used to study the mechanical behavior of cemented carbides in compression tests. The model is obtained by slicing the sample by Focused Ion Beam and reconstructing it. This model is used to ...

2025

Micromechanics reveal strain rate dependent transition between dislocation mechanisms in a dual phase high entropy alloy

Johann Michler

An equimolar NiCoFeCrGa high entropy alloy having dual-phase composition was studied, where the constituent phases exhibit distinct mechanical properties. Micropillars with various diameters were created from two differently heat treated samples, then they ...

2025

Dislocation Hardening in a New Manufacturing Route of Ferritic Oxide Dispersion-Strengthened Fe-14Cr Cladding Tube

Roland Logé

The microstructure evolution associated with the cold forming sequence of an Fe-14Cr-1W-0.3Ti-0.3Y2O3 grade ferritic stainless steel strengthened by dispersion of nano oxides (ODS) was investigated. The material, initially hot extruded at 1100 degrees C an ...

MDPI2024

Evaluation of Interface and Residual Strain of NiTi Layer Deposited on NiTiX Substrate by Laser Powder Bed Fusion

Elyas Ghafoori, Christian Leinenbach, Irene Ferretto

This study investigates the microstructure and properties of functionally graded NiTi alloy bilayers. The NiTi layer is printed by laser powder bed fusion on a NiTiX (where X is Hf or Cu) substrate prepared by vacuum arc remelting. Specimens produced with ...

Wiley-V C H Verlag Gmbh2024

Performance of energy piles foundation in hot-dominated climate: A case study in Dubai

Lyesse Laloui, Elena Ravera, Sofie Elaine ten Bosch

Energy piles represent an innovative technology that can help provide sustainable geothermal heating or cooling energy for thermal conditioning purposes. In hot-dominated climates, the interest is to inject heat in the ground and extract energy for space-c ...

Pergamon-Elsevier Science Ltd2024

The Influence of Micro- and Macrocracks on the Permeability of Granite

Marie Estelle Solange Violay

Damage zones exist around crustal faults, where micro- and macrocracks coexist and form a complex conduit network for fluid flow. The permeability of these zones can change rapidly as the crack network evolves during deformation. To investigate the relativ ...

SPRINGER WIEN2024

Effects of beam shaping on copper-steel interfaces in multi-material laser beam powder bed fusion

Seyed Amirmohammad Jamili

Multi-material laser beam powder bed fusion (PBF-LB) is a promising approach to meet industrial demands for multifunctional components, due to its enhanced freedom of design. Copper and stainless steel are interesting materials to be combined due to the hi ...

Elsevier Science Sa2024

Computational fluid-structure interaction analysis of the end-to-side radio-cephalic arteriovenous fistula

Alfio Quarteroni, Fabio Marcinno

Background and Objective: In the current work, we present a descriptive fluid-structure interaction computational study of the end -to -side radio-cephalic arteriovenous fistula. This allows us to account for the different thicknesses and elastic propertie ...

Elsevier Ireland Ltd2024

Design and assessment of an evaporating water-cooled methanation reactor for a SOE-based power-to-methane system

Philippe Aubin

The transition towards clean renewable energy sources, where wind and solar are prone to variation, requires adequate energy storage. Power-to-methane (PtM) systems can be part of the solution. Specifically, solid-oxide-electrolyser (SOE) based PtM systems ...

EPFL2024

Influence of fiber orientation on the tensile behavior of UHPFRC and reinforced UHPFRC under static and fatigue loadings

Jian Zhan

Ultra-high performance fiber reinforced cementitious composite (UHPFRC) is a modern class of cementitious building materials. Because of its superior mechanical properties and durability, it is increasingly used globally to rehabilitate, strengthen and mod ...

EPFL2024

Decomposition method to evaluate district heating/cooling network potential at urban scale

Ana Catarina Gouveia Braz, François Maréchal, Luc Girardin, Bingqian Liu

In this work, a tool to design district heating networks (DHN) is presented and applied to the city of Lausanne as a case study. The evaluation of the buildings’ heat/cooling demand is performed using a Geographic Information System (GIS) database, built f ...

Associazione Italiana Di Ingegneria Chimica2024

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Landolf-Giosef-Anastasios Rhode-Barbarigos, Tara Habibi

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

2024

Proliferation-driven mechanical compression induces signalling centre formation during mammalian organ development

Sangwoo Kim

Localized sources of morphogens, called signalling centres, play a fundamental role in coordinating tissue growth and cell fate specification during organogenesis. However, how these signalling centres are established in tissues during embryonic developmen ...

Nature Portfolio2024

Composition and Element Distribution Mapping of γ′ and γ" Phases of Inconel 718 by High-Resolution Scanning Transmission Electron Microscopy and X-ray Energy-Dispersive Spectrometry

Philippe Buffat

The main strengthening mechanism for Inconel 718 (IN718), a Ni-based superalloy, is precipitation hardening by gamma ' and gamma '' particles. It is thus essential, for good alloy performance, that precipitates with the desired chemical composition have ad ...

MDPI2024

Experimental investigation of dowel action in reinforcing bars using refined measurements

Aurelio Muttoni, Marko Pejatovic

In typical reinforced concrete design, reinforcement is designed to carry axial forces, but it can also resist transversal forces by dowel action. This is usually neglected for simplicity's sake in the design phase, but it can be accounted for either expli ...

Ernst & Sohn2024

Innovative thermophysical characterization of an ATF composite cladding: the case of silicon carbide

Andrea Cavaliere

Nuclear power is a powerful technology that plays an important role in the fight against climate change, and research is continuously engaged in studies that could further improve its safety. After the Fukushima accident, Accident Tolerant Fuels research h ...

EPFL2024

Water weakening and the compressive brittle strength of carbonates: Influence of fracture toughness and static friction

Marie Estelle Solange Violay, Corentin Jean-Marie Rémi Noël, Barnaby Padraig Fryer

Water is ubiquitous within the pore space of rocks and has been shown to affect their physical and mechanical behaviour. Indeed, water can act on the rock strength via mechanical (i.e., reducing the effective stresses) or chemical effects (e.g., mineral di ...

2024

Flash Melting Amorphous Ice

Marcel Drabbels, Ulrich Lorenz, Gabriele Bongiovanni, Constantin Richard Krüger, Nathan Junior Mowry

Water can be vitrified if it is cooled at high rates, which makes it possible to outrun crystallization in so-called no man’s land, a range of deeply supercooled temperatures where water crystallizes rapidly. Here, we study the reverse process in pure wate ...

2024

Plasmoid drift and first wall heat deposition during ITER H-mode dual-SPIs in JOREK simulations

Mengdi Kong

The heat flux mitigation during the thermal quench (TQ) by the shattered pellet injection (SPI) is one of the major elements of disruption mitigation strategy for ITER. It's efficiency greatly depends on the SPI and the target plasma parameters, and is ult ...

IOP Publishing Ltd2024

DTT toroidal field conductor samples test in Sultan: DC and AC characterization

Kamil Sedlák, Mattia Ortino, Hugues Marie Alain Bajas

The superconducting magnet system of the Divertor Tokamak Test (DTT) facility, composed of 18 toroidal field (TF) coils, 6 poloidal field coils and a central solenoid, has been designed and many procurements have been launched. Some manufacturing aspects a ...

Iop Publishing Ltd2024