Scale limitations of gas bearing supported turbocompressors for vapor compression cycles

About
Privacy
Disclaimer

Graph Chatbot

Related publications (31)

Visualization and modelling of dynamic flow in fibrous preforms for liquid composite molding

Nowadays, Liquid Composite Molding techniques are often used to manufacture high quality fiber reinforced composite parts at a relatively low cost. These involve an infiltration process, in which a liquid resin is forced to ingress into a dry fibrous porou ...

EPFL2023

Influence of Viscous Lubricant on Nucleation and Propagation of Frictional Ruptures

Marie Estelle Solange Violay, François Xavier Thibault Passelègue, Federica Paglialunga

Fluids are pervasive in the Earth's crust and saturate fractures and faults. The combination of fluids and gouge layers developing along faults can generate fluids of different viscosities. Such viscous fluids were found to influence the reactivation, fric ...

2023

Readiness evaluation of SOFC-MGT hybrid systems with carbon capture for distributed combined heat and power

Jürg Alexander Schiffmann, Jan Van Herle, Michele Gaffuri, Victoria Xu Hong He

The aggravation of climate change calls for the timely development and implementation of highly efficient, renewable, zero- or negative-emission energy solutions with high technological readiness and feasibility levels. Solid oxide fuel cells (SOFC) consti ...

Elsevier2023

Fiber pumps for wearable fluidic systems

Herbert Shea, Vito Cacucciolo, Michael James Henry Smith

Incorporating pressurized fluidic circuits into textiles can enable muscular support, thermoregulation, and haptic feedback in a convenient wearable form factor. However, conventional rigid pumps, with their associated noise and vibration, are unsuitable f ...

American Association for the Advancement of Science2023

Exploring the potential of the critical shear crack theory for reinforced and post-tensioned glass beams: Initial analysis and experiments

Alain Nussbaumer, Pieter Christian Louter, Jagoda Cupac

In the evolution of structural glass beam elements, the requirements for post-fracture load bearing capacity and safe failure behaviour have led to the development of reinforced and post-tensioned beams. Maximum bending capacity in the post-fracture state ...

2023

BamX: Rethinking Deployability in Architecture through Weaving

Mark Pauly, Yingying Ren, Tian Chen, Seiichi Eduardo Suzuki Erazo, Stefana Parascho

Deployable gridshells are a class of planar-to-spatial structures that achievea 3D curved geometry by inducing bending on a flat grid of elastic beams. However, theslender nature of these beams often conflicts with the structure’s load-bearing capacity.To ...

De Gruyter2023

The thermodynamic and life-cycle assessments of a novel charging station for electric vehicles in dynamic and steady-state conditions

Jan Van Herle, Hossein Pourrahmani, Chengzhang Xu

The current study performs the thermodynamic and life-cycle assessments (LCA) of a novel charging station in two system designs. The goal is to design an efficient charging station for electric vehicles with high efficiencies and low environmental impacts ...

Nature Portfolio2023

Vapor Deposition of Perovskite Solar Cells

Quentin Jean-Marie Armand Guesnay

Thanks to the continuous improvement of crystalline silicon (c-Si) solar cells, largely dominating the market, photovoltaic electricity is nowadays the cheapest source of energy on the market. Yet, solar energy is far from being completely harvested, as t ...

EPFL2023

Heat transfer of uncoated and nanostructure coated commercially micro-enhanced refrigeration tubes under pool boiling conditions

John Richard Thome

The heat transfer performance of commercially produced micro-enhanced tubes with and without a nanocoating was investigated under pool boiling of saturated refrigerant. These multiscale enhancements were on the outside of 19 mm horizontal copper tubes heat ...

Pergamon-Elsevier Science Ltd2023

Multiscale enhancement of refrigerant falling film boiling by combining commercially enhanced tubes with nanostructures

John Richard Thome

Multiscale surface structures offer the opportunity to combine the heat transfer enhancement provided by microscale structures with the dryout benefits provided by some nanostructures, which is particularly attractive for falling film evaporators, who have ...

Pergamon-Elsevier Science Ltd2023

Modeling and analysis of miniaturized magnetorheological valve for fluidic actuation

Sofia Lydia Ntella

Fluidic actuation enables movement in a wide range of mechanical systems, from simple laboratory devices to more complex industrial machinery. Fluids are used to generate motion of mechanical pieces. The term "fluids" encompasses two types of technologies: ...

EPFL2023

Page 2 of 2