Publications related to Investigation of process-induced strains development by fibre Bragg grating sensors in resin transfer moulded composites

Related publications (36)

Cyclic loading of WC-Ni by FEM with a realistic 3D morphology

Daniele Mari, Lucas Eric Jacques Degeneve

A Finite Element Model produced from a real WC-10wt.%Co sample is used to study the mechanical behavior of cemented carbides in compression tests. The model is obtained by slicing the sample by Focused Ion Beam and reconstructing it. This model is used to ...

2025

Development of a Sustainable Thermoplastic Composite Material Using Manicaria saccifera Fabric and Elium® Resin

Véronique Michaud

The massive production of nonrenewable materials has exacerbated global environmental challenges, necessitating the development of sustainable alternatives. This study explores the potential of the Manicaria saccifera fabric, an indigenous Colombian natura ...

2025

Mitigation of infusion and cure-induced defects for thick thermosetting composites: Current challenges and future trends

Véronique Michaud

The composite part industry is currently dominated by thin-section geometries. However, thick composites gain interest in many applications where monolithic parts are required, such as foils, wind mill root blades, and so forth. Their manufacturing continu ...

2025

The Influence of Micro- and Macrocracks on the Permeability of Granite

Marie Estelle Solange Violay

Damage zones exist around crustal faults, where micro- and macrocracks coexist and form a complex conduit network for fluid flow. The permeability of these zones can change rapidly as the crack network evolves during deformation. To investigate the relativ ...

SPRINGER WIEN2024

Self-catalysed frontal polymerisation enables fast and low-energy processing of fibre reinforced polymer composites

Véronique Michaud, Baris Çaglar, Jacobus Gerardus Rudolph Staal

Frontal polymerisation has the potential to bring unprecedented reductions in energy demand and process time to produce fibre reinforced polymer composites. Production of epoxy-based fibre reinforced polymer parts with high fibre volume content, commonly e ...

2024

Near-Room-Temperature Detection of Aromatic Compounds with Inkjet-Printed Plasticized Polymer Composites

Jürgen Brugger, Thomas Maeder, Mohammadmahdi Kiaee

Chemiresistive gas sensors composed of a thermoplastic polymer matrix and conductive fillers offer various advantages for detecting volatile organic compounds (VOCs), including low power consumption due to near-room-temperature operation, high sensitivity, ...

Amer Chemical Soc2024

Two-dimensional quasi-static delamination in composite laminates under Mode-I and Mode-II conditions

Congzhe Wang

Fiber-polymer composites consist of a polymer matrix and reinforcing fibers made of various materials. These composites exhibit exceptional properties, such as a high strength-to-weight ratio and excellent corrosion resistance, which has led to their incre ...

EPFL2024

Numerical investigation of two-dimensional Mode-II delamination in composite laminates

Thomas Keller, Anastasios Vassilopoulos, Congzhe Wang

Existing standards for delamination tests on composite materials typically employ one-dimensional (1D) beam specimens. However, such specimens may not represent real delamination scenarios in composite structures, where cracks tend to propagate in two dime ...

Elsevier Sci Ltd2024

Modeling friction and wear using an adaptive discrete-continuum coupling

Manon Eugénie Voisin--Leprince

When two objects slide against each other, wear and friction occur at their interface. The accumulation of wear forms what is commonly referred to as a ``third-body''. Understanding third-body evolution has significant applications in industry, where contr ...

EPFL2024

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Xhemsi Malja

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Diego Hernández Fraile

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

EPFL2024

Strain engineering and strain measurement by spring tethers on suspended epitaxial GaN-on-Si photonic crystal devices

Romuald Houdré, Jun Wang

Suspended epitaxial gallium nitride (GaN) on silicon (Si) photonic crystal devices suffer from large residual tensile strain, especially for long waveguides, because fine structures tend to crack due to large stress. By introducing spring-like tethers, des ...

Iop Publishing Ltd2024

3D Printing of Double Network Granular Elastomers with Locally Varying Mechanical Properties

Benjamin François Régis Tiberghien, Esther Amstad, Eva Jeanne Baur

Fast advances in the design of soft actuators and robots demand for new soft materials whose mechanical properties can be changed over short length scales. Elastomers can be formulated as highly stretchable or rather stiff materials and hence, are attracti ...

Wiley-V C H Verlag Gmbh2024

A novel fatigue life prediction methodology based on energy dissipation in viscoelastic materials, synergistic effects of stress level, stress ratio, and temperature

Thomas Keller, Lulu Liu, Abdolvahid Movahedirad

This work introduces a new methodology to predict the fatigue life of viscoelastic materials by considering the creep effect on fatigue behavior under the concurrent effects of stress level, stress ratio, and temperature. The model established based on the ...

2024

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Landolf-Giosef-Anastasios Rhode-Barbarigos, Tara Habibi

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

2024

Geospatial Tools and Remote Sensing Strategies for Timely Humanitarian Response: A Case Study on Drought Monitoring in Eswatini

Jérôme Chenal

This article explores the escalating impact of natural disasters, particularly droughts, in the Southern African Development Community (SADC), with a specific focus on Eswatini. Over the last century, approximately 63 million people in SADC countries have ...

MDPI2024

Fungal mycelia: From innovative materials to promising products: Insights and challenges

Wenjing Sun

In transitioning toward a sustainable economy, mycelial materials are recognized for their adaptability, biocompatibility, and eco-friendliness. This paper updates the exploration of mycelial materials, defining their scope and emphasizing the need for pre ...

Aip Publishing2024

Insights from an extensive triaxial testing campaign on a shale for comparative site characterization of a deep geological repository

Lyesse Laloui, Alessio Ferrari, Eleonora Crisci

Several boreholes were drilled for site comparison of a deep geological repository (DGR) in Northern Switzerland. The main target of the exploration program was the >100m thick Opalinus Clay, the designated host rock encountered at approximately 450 to 100 ...

Elsevier2024

Highly anisotropic carbon fiber electrodes for DEAs and their dynamic non-monotonic conductive properties

Yves Perriard, Stefania Maria Aliki Konstantinidi

A common method for creating compliant electrodes for dielectric elastomer actuators (DEAs) and soft sensors is to incorporate electrically conductive carbon particles into a polymer matrix. However, using unidirectional aligned carbon fibers instead not o ...

Society of Photo-Optical Instrumentation Engineers (SPIE)2024

Decarbonization potential of steel fibre-reinforced limestone calcined clay cement concrete one-way slabs

Hisham Tarek Mohamed Hafez, Beatrice Malchiodi

This study deals with a comparison of the environmental performance of one-way slabs utilizing steel fibrereinforced limestone calcined clay cement (LC3) concrete with the control case of Ordinary Portland cement concrete. The experimental program constitu ...

Elsevier Sci Ltd2024