Lecture

CG: IC Design I

Graph Chat

Chat with Graph Search

Ask any question about EPFL courses, lectures, exercises, research, news, etc. or try the example questions below.

DISCLAIMER: The Graph Chatbot is not programmed to provide explicit or categorical answers to your questions. Rather, it transforms your questions into API requests that are distributed across the various IT services officially administered by EPFL. Its purpose is solely to collect and recommend relevant references to content that you can explore to help you answer your questions.

In course

EE-320: Analog IC design

Introduction to the design of analog CMOS integrated circuits at the transistor level. Understanding and design of basic structures. ...

Description

This lecture covers the organization of the course, review of BJT and MOS transistors, MOS large and small-signal models, single-stage amplifiers, cascode, differential pairs, practical exercises on Cadence, current mirrors, and Q&A sessions. It also discusses the common-source, source-follower, and source-drain configurations, as well as the large signal analysis and impedance transformation by MOSFETs. The lecture concludes with examples on calculating voltage gain and output resistance of a common-gate stage, and introduces the cascode stage, highlighting its benefits in circuit design.

Instructor

Mahsa Shoaran

Official source

Ontological neighbourhood

Physics

Electromagnetism: Electrical networks

Related concepts (32)

Transistor

A transistor is a semiconductor device used to amplify or switch electrical signals and power. It is one of the basic building blocks of modern electronics. It is composed of semiconductor material, usually with at least three terminals for connection to an electronic circuit. A voltage or current applied to one pair of the transistor's terminals controls the current through another pair of terminals. Because the controlled (output) power can be higher than the controlling (input) power, a transistor can amplify a signal.

Differential signalling

Differential signalling is a method for electrically transmitting information using two complementary signals. The technique sends the same electrical signal as a differential pair of signals, each in its own conductor. The pair of conductors can be wires in a twisted-pair or ribbon cable or traces on a printed circuit board. Electrically, the two conductors carry voltage signals which are equal in magnitude, but of opposite polarity. The receiving circuit responds to the difference between the two signals, which results in a signal with a magnitude twice as large.

Bipolar junction transistor

A bipolar junction transistor (BJT) is a type of transistor that uses both electrons and electron holes as charge carriers. In contrast, a unipolar transistor, such as a field-effect transistor (FET), uses only one kind of charge carrier. A bipolar transistor allows a small current injected at one of its terminals to control a much larger current flowing between the terminals, making the device capable of amplification or switching. BJTs use two p–n junctions between two semiconductor types, n-type and p-type, which are regions in a single crystal of material.

Amplifier

An amplifier, electronic amplifier or (informally) amp is an electronic device that can increase the magnitude of a signal (a time-varying voltage or current). It is a two-port electronic circuit that uses electric power from a power supply to increase the amplitude (magnitude of the voltage or current) of a signal applied to its input terminals, producing a proportionally greater amplitude signal at its output. The amount of amplification provided by an amplifier is measured by its gain: the ratio of output voltage, current, or power to input.

Field-effect transistor

The field-effect transistor (FET) is a type of transistor that uses an electric field to control the flow of current in a semiconductor. FETs (JFETs or MOSFETs) are devices with three terminals: source, gate, and drain. FETs control the flow of current by the application of a voltage to the gate, which in turn alters the conductivity between the drain and source. FETs are also known as unipolar transistors since they involve single-carrier-type operation.

Related lectures (32)

Electronic Circuits and Systems

Covers the basics of electronics, amplifiers, transistors, and small signal models for transistors.

Common Source Amplifier Exercise

Covers the exercise on determining key parameters of a common source amplifier.

CMOS Gates and Logic Systems

Covers the basics of CMOS gates and Logic Systems, highlighting the advantages of CMOS over TTL gates.

Designing NMOS Amplifiers: Key Parameters and Techniques

Covers the design principles and key parameters for NMOS amplifiers, focusing on transconductance and gain optimization.

Digital Integrated Circuits: Evolution and Design