Load–store architectureIn computer engineering, a load–store architecture (or a register–register architecture) is an instruction set architecture that divides instructions into two categories: memory access (load and store between memory and registers) and ALU operations (which only occur between registers). Some RISC architectures such as PowerPC, SPARC, RISC-V, ARM, and MIPS are load–store architectures. For instance, in a load–store approach both operands and destination for an ADD operation must be in registers.
Processor designProcessor design is a subfield of computer science and computer engineering (fabrication) that deals with creating a processor, a key component of computer hardware. The design process involves choosing an instruction set and a certain execution paradigm (e.g. VLIW or RISC) and results in a microarchitecture, which might be described in e.g. VHDL or Verilog. For microprocessor design, this description is then manufactured employing some of the various semiconductor device fabrication processes, resulting in a die which is bonded onto a chip carrier.
Central processing unitA central processing unit (CPU)—also called a central processor or main processor—is the most important processor in a given computer. Its electronic circuitry executes instructions of a computer program, such as arithmetic, logic, controlling, and input/output (I/O) operations. This role contrasts with that of external components, such as main memory and I/O circuitry, and specialized coprocessors such as graphics processing units (GPUs). The form, design, and implementation of CPUs have changed over time, but their fundamental operation remains almost unchanged.
Index registerAn index register in a computer's CPU is a processor register (or an assigned memory location) used for pointing to operand addresses during the run of a program. It is useful for stepping through strings and arrays. It can also be used for holding loop iterations and counters. In some architectures it is used for read/writing blocks of memory. Depending on the architecture it maybe a dedicated index register or a general-purpose register.
Speculative executionSpeculative execution is an optimization technique where a computer system performs some task that may not be needed. Work is done before it is known whether it is actually needed, so as to prevent a delay that would have to be incurred by doing the work after it is known that it is needed. If it turns out the work was not needed after all, most changes made by the work are reverted and the results are ignored. The objective is to provide more concurrency if extra resources are available.
Execution (computing)Execution in computer and software engineering is the process by which a computer or virtual machine reads and acts on the instructions of a computer program. Each instruction of a program is a description of a particular action which must be carried out, in order for a specific problem to be solved. Execution involves repeatedly following a 'fetch–decode–execute' cycle for each instruction done by control unit. As the executing machine follows the instructions, specific effects are produced in accordance with the semantics of those instructions.
Status registerA status register, flag register, or condition code register (CCR) is a collection of status flag bits for a processor. Examples of such registers include FLAGS register in the x86 architecture, flags in the program status word (PSW) register in the IBM System/360 architecture through z/Architecture, and the application program status register (APSR) in the ARM Cortex-A architecture. The status register is a hardware register that contains information about the state of the processor.
R3000The R3000 is a 32-bit RISC microprocessor chipset developed by MIPS Computer Systems that implemented the MIPS I instruction set architecture (ISA). Introduced in June 1988, it was the second MIPS implementation, succeeding the R2000 as the flagship MIPS microprocessor. It operated at 20, 25 and 33.33 MHz. The MIPS 1 instruction set is small compared to those of the contemporary 80x86 and 680x0 architectures, encoding only more commonly used operations and supporting few addressing modes.
Hazard (computer architecture)In the domain of central processing unit (CPU) design, hazards are problems with the instruction pipeline in CPU microarchitectures when the next instruction cannot execute in the following clock cycle, and can potentially lead to incorrect computation results. Three common types of hazards are data hazards, structural hazards, and control hazards (branching hazards). There are several methods used to deal with hazards, including pipeline stalls/pipeline bubbling, operand forwarding, and in the case of out-of-order execution, the scoreboarding method and the Tomasulo algorithm.
Write once read manyWrite once read many (WORM) describes a data storage device in which information, once written, cannot be modified. This write protection affords the assurance that the data cannot be tampered with once it is written to the device, excluding the possibility of data loss from human error, computer bugs, or malware. On ordinary (non-WORM) data storage devices, the number of times data can be modified is limited only by the lifespan of the device, as modification involves physical changes that may cause wear to the device.
R8000The R8000 is a microprocessor chipset developed by MIPS Technologies, Inc. (MTI), Toshiba, and Weitek. It was the first implementation of the MIPS IV instruction set architecture. The R8000 is also known as the TFP, for Tremendous Floating-Point, its name during development. Development of the R8000 started in the early 1990s at Silicon Graphics, Inc. (SGI). The R8000 was specifically designed to provide the performance of circa 1990s supercomputers with a microprocessor instead of a central processing unit (CPU) built from many discrete components such as gate arrays.
Classic RISC pipelineIn the history of computer hardware, some early reduced instruction set computer central processing units (RISC CPUs) used a very similar architectural solution, now called a classic RISC pipeline. Those CPUs were: MIPS, SPARC, Motorola 88000, and later the notional CPU DLX invented for education. Each of these classic scalar RISC designs fetches and tries to execute one instruction per cycle. The main common concept of each design is a five-stage execution instruction pipeline.
