Mediaspace scheduled maintenance: Aug 25, 2026 07:00 - 12:00 AM. During this time, videos will be temporarily unavailable. Check status updates.

Lecture

Introduction to Boiling

In course

ME-341: Heat and mass transfer

This course covers fundamentals of heat transfer and applications to practical problems. Emphasis will be on developing a physical and analytical understanding of conductive, convective, and radiative heat transfer. ...

Description

This lecture provides an introduction to boiling and condensation, covering topics such as the boiling curve, different modes of boiling, and the fundamentals of heat transfer in boiling phenomena. It explains the heat transfer mechanisms involved in boiling, including nucleate boiling, film boiling, and critical heat flux. The lecture also discusses the complexities of the boiling phenomenon, illustrated by the boiling curve and observations from saturated pool boiling experiments.

This video is available exclusively on Mediaspace for a restricted audience. Please log in to MediaSpace to access it if you have the necessary permissions.

Watch on Mediaspace

Instructor

Giulia Tagliabue

Dr. Giulia Tagliabue is an Assistant Professor at the Institute of Mechanical Engineering (IGM). She obtained her B.S. and M.S degrees cum laude in Mechanical Engineering from the University of Udine in Italy. Concurrently she also obtained the diploma from the Scuola Normale Superiore of Udine. In 2015 she obtained her PhD in Mechanical Engineering from ETH Zurich with a thesis on nanophotonic design for light-to-heat and light-to-charge conversion devices. In 2015 Dr. Tagliabue was awarded the Early Mobility Fellowship from the Swiss National Science Foundation and moved to Caltech as a PostDoctoral fellow. In 2017, thanks to the award of an Advanced Mobility Fellowship, she prolonged her stay at Caltech. Here, in collaboration with the Joint Center for Artificial Photosynthesis (JCAP) she investigated coupled light, heat and charge transfer processes in nanophotonic structures and low-dimensional materials for photoelectrochemical and photovoltaic sustainable energy conversion.

Official source

Ontological neighbourhood

Physics

Condensed matter physics: Phase transitions

Related concepts (32)

Boiling

Boiling is the rapid phase transition from liquid to gas or vapor; the reverse of boiling is condensation. Boiling occurs when a liquid is heated to its boiling point, so that the vapour pressure of the liquid is equal to the pressure exerted on the liquid by the surrounding atmosphere. Boiling and evaporation are the two main forms of liquid vapourization. There are two main types of boiling: nucleate boiling where small bubbles of vapour form at discrete points, and critical heat flux boiling where the boiling surface is heated above a certain critical temperature and a film of vapour forms on the surface.

Boiling point

The boiling point of a substance is the temperature at which the vapor pressure of a liquid equals the pressure surrounding the liquid and the liquid changes into a vapor. The boiling point of a liquid varies depending upon the surrounding environmental pressure. A liquid in a partial vacuum, i.e., under a lower pressure, has a lower boiling point than when that liquid is at atmospheric pressure. Because of this, water boils at under standard pressure at sea level, but at at altitude.

Heat transfer

Heat transfer is a discipline of thermal engineering that concerns the generation, use, conversion, and exchange of thermal energy (heat) between physical systems. Heat transfer is classified into various mechanisms, such as thermal conduction, thermal convection, thermal radiation, and transfer of energy by phase changes. Engineers also consider the transfer of mass of differing chemical species (mass transfer in the form of advection), either cold or hot, to achieve heat transfer.

Nucleate boiling

In fluid thermodynamics, nucleate boiling is a type of boiling that takes place when the surface temperature is hotter than the saturated fluid temperature by a certain amount but where the heat flux is below the critical heat flux. For water, as shown in the graph below, nucleate boiling occurs when the surface temperature is higher than the saturation temperature (TS) by between . The critical heat flux is the peak on the curve between nucleate boiling and transition boiling.

Critical heat flux

In the study of heat transfer, critical heat flux (CHF) is the heat flux at which boiling ceases to be an effective form of transferring heat from a solid surface to a liquid. Boiling systems are those in which liquid coolant absorbs energy from a heated solid surface and undergoes a change in phase. In flow boiling systems, the saturated fluid progresses through a series of flow regimes as vapor quality is increased. In systems that utilize boiling, the heat transfer rate is significantly higher than if the fluid were a single phase (i.

Related lectures (42)

Transient Heat Transfer Log in to Mediaspace to watch this video

Covers exercises on heat and mass transfer, including multimodal heat transfer and transient conduction.

Introduction to Free Convection: Governing Equations Log in to Mediaspace to watch this video

Explores free convection, laminar flow boundary layer equations, and heat transfer principles.

Internal Forced Convection: Hydrodynamic Aspects Log in to Mediaspace to watch this video

Covers the hydrodynamic and thermal aspects of internal forced convection.

Forced Convection Correlations Log in to Mediaspace to watch this video

Explores forced external convection correlations and the procedure for solving convection problems, including the comparison of velocity and thermal boundary layers.

Forced Boiling: Internal Flow Log in to Mediaspace to watch this video