Mediaspace scheduled maintenance: Aug 25, 2026 07:00 - 12:00 AM. During this time, videos will be temporarily unavailable. Check status updates.

Lecture

Noise Calculation in Circuits

In course

EE-594: Smart sensors for IoT

This lecture provides insights in the design and technologies of Internet-of-Things sensor nodes, with focus on low power technologies. The lectures alternate every two weeks between sensing technologies of various kinds (prof. Ionescu) and their integrate ...

Description

This lecture covers the analysis of noise in continuous-time circuits, focusing on noise calculation in small-signal and input-referred noise circuits. Examples include transresistance and non-inverting amplifiers. It also discusses the noise variance in 1st-order low-pass filters and the impact of feedback on noise and distortion. The instructor emphasizes the importance of accurately estimating and simulating noise in circuits, especially with decreasing supply voltage.

This video is available exclusively on Mediaspace for a restricted audience. Please log in to MediaSpace to access it if you have the necessary permissions.

Watch on Mediaspace

Official source

Ontological neighbourhood

Information engineering

Signal processing: Digital image processing

Physics

Electromagnetism: Electrical networks

Related concepts (32)

Operational amplifier

An operational amplifier (often op amp or opamp) is a DC-coupled high-gain electronic voltage amplifier with a differential input and, usually, a single-ended output. In this configuration, an op amp produces an output potential (relative to circuit ground) that is typically 100,000 times larger than the potential difference between its input terminals. The operational amplifier traces its origin and name to analog computers, where they were used to perform mathematical operations in linear, non-linear, and frequency-dependent circuits.

Noise figure

Noise figure (NF) and noise factor (F) are figures of merit that indicate degradation of the signal-to-noise ratio (SNR) that is caused by components in a signal chain. These figures of merit are used to evaluate the performance of an amplifier or a radio receiver, with lower values indicating better performance. The noise factor is defined as the ratio of the output noise power of a device to the portion thereof attributable to thermal noise in the input termination at standard noise temperature T0 (usually 290 K).

Amplifier

An amplifier, electronic amplifier or (informally) amp is an electronic device that can increase the magnitude of a signal (a time-varying voltage or current). It is a two-port electronic circuit that uses electric power from a power supply to increase the amplitude (magnitude of the voltage or current) of a signal applied to its input terminals, producing a proportionally greater amplitude signal at its output. The amount of amplification provided by an amplifier is measured by its gain: the ratio of output voltage, current, or power to input.

Signal-to-noise ratio

Signal-to-noise ratio (SNR or S/N) is a measure used in science and engineering that compares the level of a desired signal to the level of background noise. SNR is defined as the ratio of signal power to noise power, often expressed in decibels. A ratio higher than 1:1 (greater than 0 dB) indicates more signal than noise. SNR is an important parameter that affects the performance and quality of systems that process or transmit signals, such as communication systems, audio systems, radar systems, imaging systems, and data acquisition systems.

Noise

Noise is unwanted sound considered unpleasant, loud, or disruptive to hearing. From a physics standpoint, there is no distinction between noise and desired sound, as both are vibrations through a medium, such as air or water. The difference arises when the brain receives and perceives a sound. Acoustic noise is any sound in the acoustic domain, either deliberate (e.g., music or speech) or unintended. In contrast, noise in electronics may not be audible to the human ear and may require instruments for detection.

Related lectures (37)

Understanding Noise in Electrical Systems

Explores noise sources, Fluctuation-Dissipation Theorem, amplifier noise, interference effects, and quantization error in electrical systems.

Noise in Data Acquisition

Explores noise sources in data acquisition, including thermal, shot, and amplifier noise, as well as the effects of ADC noise.

Noise Reduction Techniques

Explores noise reduction techniques in electrical systems, covering concepts like Fourier transform, impedance matching, and dithering.

Hardware Technologies and Applications

Explores hardware technologies, quantum electronics, cryogenic systems, quantum computing, and ADC architectures.