Mediaspace scheduled maintenance: Aug 25, 2026 07:00 - 12:00 AM. During this time, videos will be temporarily unavailable. Check status updates.

Lecture

Microwave Circuit Characterization II

In course

EE-445: Microwaves, the basics of wireless communications

This course is an introduction to microwaves and microwave passive circuits. A special attention is given to the introduction of the notion of distributed circuits and to the scattering matrix ...

Description

This lecture covers the characterization of microwave circuits from slides 10 to 30. It explains the definitions of voltage, current, impedance, power flux, and impedance matrix in microwave circuits. The lecture also delves into the concept of single port elements, impedance and admittance, equivalent T circuit, scattering parameters, and normalized wave amplitudes.

This video is available exclusively on Mediaspace for a restricted audience. Please log in to MediaSpace to access it if you have the necessary permissions.

Watch on Mediaspace

Instructor

Anja Skrivervik

Anja Skrivervik obtained her electrical engineering degree from Ecole Polytechnique Fédérale de Lausanne in 1986, and her PhD from the same institution in 1992, for which she received the Latsis award. After a stay at the University of Rennes as an invited Research Fellow and two years in the industry, she returned part time to EPFL as an Assistant Professor in 1996, and is now a Professeur Titulaire at this institution, where she is the head of the Microwave and Antenna Group. Her research activities include electrically small antennas, antennas in biological media, periodic structures, reflect- and tranmitarrays, and numerical techniques for electromagnetics. She is author or co-author of more than 200 peer reviewed scientific publications. Her teaching activities include courses on microwaves and antennas, and she has course at Bachelor, Master and PhD levels. She was director of the EE section form 1996-2000, and is currently the director of the EE doctoral school at EPFL. She is very active in European collaboration and European projects. She was the chairperson of the Swiss URSI until 2012, is a Board member of the European School on Antennas and is frequently requested to review research programs and centers in Europe. She is a member of the board of directors of the European Association on Antennas and Propagation (EurAAP) since 2017.

Official source

Related concepts (32)

Electrical impedance

In electrical engineering, impedance is the opposition to alternating current presented by the combined effect of resistance and reactance in a circuit. Quantitatively, the impedance of a two-terminal circuit element is the ratio of the complex representation of the sinusoidal voltage between its terminals, to the complex representation of the current flowing through it. In general, it depends upon the frequency of the sinusoidal voltage.

Characteristic impedance

The characteristic impedance or surge impedance (usually written Z0) of a uniform transmission line is the ratio of the amplitudes of voltage and current of a single wave propagating along the line; that is, a wave travelling in one direction in the absence of reflections in the other direction. Alternatively, and equivalently, it can be defined as the input impedance of a transmission line when its length is infinite. Characteristic impedance is determined by the geometry and materials of the transmission line and, for a uniform line, is not dependent on its length.

Input impedance

The input impedance of an electrical network is the measure of the opposition to current (impedance), both static (resistance) and dynamic (reactance), into a load network that is external to the electrical source network. The input admittance (the reciprocal of impedance) is a measure of the load network's propensity to draw current. The source network is the portion of the network that transmits power, and the load network is the portion of the network that consumes power.

Impedance matching

In electronics, impedance matching is the practice of designing or adjusting the input impedance or output impedance of an electrical device for a desired value. Often, the desired value is selected to maximize power transfer or minimize signal reflection. For example, impedance matching typically is used to improve power transfer from a radio transmitter via the interconnecting transmission line to the antenna. Signals on a transmission line will be transmitted without reflections if the transmission line is terminated with a matching impedance.

Impedance parameters

Impedance parameters or Z-parameters (the elements of an impedance matrix or Z-matrix) are properties used in electrical engineering, electronic engineering, and communication systems engineering to describe the electrical behavior of linear electrical networks. They are also used to describe the small-signal (linearized) response of non-linear networks. They are members of a family of similar parameters used in electronic engineering, other examples being: S-parameters, Y-parameters, H-parameters, T-parameters or ABCD-parameters.

Related lectures (50)

Electroacoustics: Impedance and Wave Behavior

Explores impedance, wave behavior, and equivalent diagrams in electroacoustics, focusing on tube length, terminal impedance, and wave transmission.

Impedances and Impedance Networks MOOC: Electrical engineering I

Covers the representation of impedances, voltage and current dividers, and impedance networks in electrical engineering.

Frequency Domain Study: Acoustic Response Analysis

Explores the Frequency Domain study in COMSOL for analyzing acoustic responses to harmonic excitation in various fields.

Mechanical-Acoustic Coupling

Covers the coupling between vibrating systems and acoustic fields, focusing on radiation impedance and equivalent diagrams.

Sinusoidal Circuits: Examples and Impedances MOOC: Electrical engineering I