Mediaspace scheduled maintenance: Aug 25, 2026 07:00 - 12:00 AM. During this time, videos will be temporarily unavailable. Check status updates.

Concept

Plastic extrusion

Related publications (27)

Near-Room-Temperature Detection of Aromatic Compounds with Inkjet-Printed Plasticized Polymer Composites

Jürgen Brugger, Thomas Maeder, Mohammadmahdi Kiaee

Chemiresistive gas sensors composed of a thermoplastic polymer matrix and conductive fillers offer various advantages for detecting volatile organic compounds (VOCs), including low power consumption due to near-room-temperature operation, high sensitivity, ...

Amer Chemical Soc2024

Large-Scale Hollow-Core 3D Printing: Variable Cross-Section and Printing Features for Lightweight Plastic Elements

Marianthi Eririni Kladeftira

Hollow-core 3D printing (HC3DP) proposes a new method for the production of lightweight, material-efficient thermoplastic 3D printed elements. This new fabrication approach promises material savings of 50-80%, while increasing the extrusion rate significan ...

Mary Ann Liebert, Inc2024

Thermoplastic Toughening of a Semiaromatic Polyamide with an Amino-telechelic Polyethylene

John Christopher Plummer, Holger Frauenrath, Michael Alan Giffin

Semiaromatic polyamides are used for metal replacementin advancedengineering applications to reduce weight and improve efficiency,but their range of application is limited by their inherent lack ofductility and toughness. Here, we combined semiaromatic pol ...

AMER CHEMICAL SOC2023

Tailoring the performance of nanocellulose-based multilayer-barrier paperboard using biodegradable-thermoplastics, pigments, and plasticizers

Tiffany Abitbol

In this work a multilayer barrier paperboard was produced in a roll-to-roll process by slot-die coating of nanocellulose (microfibrillated cellulose or carboxymethylated cellulose nanofibrils) followed by extrusion coating of biodegradable thermoplastics ( ...

SPRINGER2023

A novel interfacial polymerization assisted phase inversion process for the facile fabrication of ion-selective nanofiltration membranes

Zongyao Zhou

Interfacial polymerization (IP) and non-solvent induced phase inversion (NIPS) are the two most commonly used mainstream technologies to fabricate separation membranes. Taking their advantages, we developed a simple, facile and scalable method to integrate ...

Elsevier Science Sa2023

A multi-material robotic finger with integrated proprioceptive and tactile capabilities produced with a circular process

Josephine Anna Eleanor Hughes, Kai Christian Junge, Antonia Georgopoulou Papadonikolaki

When developing or designing biomimetic robotic fingers with rigid and soft components and integrated sensors, fabrication is often a bottle-neck when assembling and casting processing techniques are used. This study introduces a thermoplastic multi-materi ...

IEEE2023

Scaling Description of Creep Flow in Amorphous Solids

Matthieu Wyart, Thomas Willem Jan de Geus, Marko Popovic, Wencheng Ji

Amorphous solids such as coffee foam, toothpaste, or mayonnaise display a transient creep flow when a stress E is suddenly imposed. The associated strain rate is commonly found to decay in time as gamma_ -t-nu, followed either by arrest or by a sudden flui ...

AMER PHYSICAL SOC2022

Sustainable polyesters via direct functionalization of lignocellulosic sugars

François Maréchal, Véronique Michaud, Yves Leterrier, Harm-Anton Klok, Jeremy Luterbacher, Adrien Julien Demongeot, Graham Reid Dick, Maxime Alexandre Clément Hedou

The development of sustainable plastics from abundant renewable feedstocks has been limited by the complexity and efficiency of their production, as well as their lack of competitive material properties. Here we demonstrate the direct transformation of the ...

2022

Design of experiments to investigate multi-additive cellulose nanocrystal films

Tiffany Abitbol

Cellulose nanocrystal (CNC) suspensions can self-assemble into chiral nematic films upon the slow evaporation of water. These films are brittle, as indicated by their fracturing instead of plastically deforming once they are fully elastically deformed. Thi ...

FRONTIERS MEDIA SA2022

Nature-inspired Circular-economy Recycling (NaCRe) for Proteins

Simone Giaveri

Since a few decades our planet has been loaded with billion tons of synthetic polymer-based materials, commonly named plastics. The large scale of plastic production, associated with its limited recyclability, are the driving force for the accumulation of ...

EPFL2021

Microstructural controls of anticrack nucleation in highly porous brittle solids

Johan Alexandre Philippe Gaume, Henning Löwe

Porous brittle solids have the ability to collapse and fail even under compressive stresses. In fracture mechanics, this singular behavior, often referred to as anticrack, demands for appropriate continuum models to predict the catastrophic failure. To ide ...

Nature Research2020

Biodegradation and Antimicrobial Properties of Zinc Oxide-Polymer Composite Materials for Urinary Stent Applications

Lorenzo Lucherini

Research advancements in the field of urinary stents have mainly been in the selection of materials and coatings to address commonly faced problems of encrustation and bacterial adhesion. In this study, polylactic acid (PLA) and polypropylene (PP) were eva ...

2020

Modeling, predicting and mining metabolism at atom-level resolution

Jasmin Maria Hafner

Living organisms can catalyze many thousands of biochemical reactions that they use to convert energy and matter, which provides them with the essentials for life. The sum of these chemical reactions happening in an organism is called metabo-lism. Understa ...

EPFL2020

Dynamic study of contact damping in martensitic stainless steels using nano-indentation

Philippe Spätig, Hans-Peter Seifert

The study was undertaken to gain insight into the micro-mechanisms controlling plasticity at the micrometer scale of elastic-plastic metallic alloys. Dynamic nano-indentation tests, where a small harmonic force amplitude is superimposed during loading, ref ...

ELSEVIER2020

A High Resolution Digital Image Correlation Study under Multiaxial Loading

Helena Van Swygenhoven, Wei-Neng Hsu

In this study, a miniaturized cruciform-shaped sample geometry which allows reaching high plastic strain under equibiaxial loading with reduced thickness at the test section is presented. The thinning method results in excellent surface quality that can be ...

SPRINGER2019

The role of atomistic simulations in probing hydrogen effects on plasticity and embrittlement in metals

William Curtin, Ali Tehranchi

Atomistic simulations are a powerful complement to experimental probes for understanding the nanoscale processes associated with the effects of hydrogen (H) on plasticity and fracture that are the underlying causes of hydrogen embrittlement (HE). Current e ...

PERGAMON-ELSEVIER SCIENCE LTD2019

Pore Size Manipulation in 3D Printed Cryogels Enables Selective Cell Seeding

Philippe Renaud, Arnaud Bertsch, Thomas Michael Braschler, Ariane Rochat, Amélie Barbara Hildegarde Béduer, Ludovic Serex

Cryogels are macroporous materials that display remarkable properties, such as high pore interconnection, large surface to volume ratio, and high mechanical stability, making them good candidates for 3D cell culture. However, shaping cryogels remains chall ...

Wiley2018

Scaling description of non-local rheology

Matthieu Wyart

The plastic flow of amorphous materials displays non-local effects, characterized by a cooperativity length scale xi. We argue that these effects enter in the more general description of surface phenomena near critical points. Using this approach, we obtai ...

Royal Society of Chemistry2017

Ensayos cuasi-estáticos cíclicos de muros delgados de concreto reforzado en edificios colombianos

Katrin Beyer, João Saraiva Esteves Pacheco de Almeida

The use of thin reinforced concrete walls (thickness of 8 to 12 cm) in Latin America has become a popular building construction practice in the last two decades. Several existing studies indicate that the inelastic deformation capacity could be limited and ...

2017

Softening and hardening of yield stress by hydrogen–solute interactions

William Curtin, Binglun Yin, Ali Tehranchi

Hydrogen atoms have a wide variety of effects on the mechanical performance of metals, and the underlying mechanisms associated with effects on plastic flow and embrittlement remain to be discovered or validated. Here, the reduction in the plastic flow str ...

Taylor & Francis2017