Synchrotron light source

Natural sciences
Physics
Particle physics
Particle accelerators

About
Privacy
Disclaimer

Graph Chatbot

Related publications (30)

Page 2 of 2

Rotation measure and synchrotron emission signatures in simulations of magnetized galactic discs

Salim Bennouna, Yoan Rappaz

We analyse observational signatures of magnetic fields for simulations of a Milky Way-like disc with supernova-driven interstellar turbulence and self-consistent chemical processes. In particular, we post-process two simulations data sets of the SILCC Proj ...

OXFORD UNIV PRESS2022

Synchrotron Radiation and Sensors: A History of Synergies

Giorgio Margaritondo

Synchrotron radiation has emerged over more than one-half century as a gigantic worldwide enterprise involving tens of thousands of researchers. Its history has been continuously and strongly linked to the technical progress of sensors. We review here diff ...

IEEE-INST ELECTRICAL ELECTRONICS ENGINEERS INC2021

Gigahertz Frame Rate Imaging of Charge-Injection Dynamics in a Molecular Light Source

Klaus Kern, Anna Maria Roslawska, Abhishek Grewal

Light sources on the scale of single molecules can be addressed and characterized at their proper sub-nanometer scale by scanning tunneling microscopy-induced luminescence (STML). Such a source can be driven by defined short charge pulses while the lumines ...

AMER CHEMICAL SOC2021

Tomographic reconstruction of the runaway distribution function in TCV using multispectral synchrotron images

Basil Duval, Joan Decker, Umar Sheikh, Artur Perek

Synchrotron radiation observed in a quiescent Tokamak a Configuration Variable (TCV) runaway discharge is studied using filtered camera images targeting three distinct wavelength intervals. Through the tomographic simultaneous algebraic reconstruction tech ...

IOP Publishing Ltd2021

Description of beam instabilities in synchrotrons with wakefields and space charge forces using the circulant matrix model

Tatiana Pieloni, Xavier Buffat, Adrian Oeftiger

A new model for the description of beam instabilities in synchrotrons featuring wakefields and space charge forces is proposed, using the circulant matrix approach. The predictions of this model are discussed in light of past ones, with a particular emphas ...

2021

Two-dimensional correlation analysis for x-ray photoelectron spectroscopy

Christoph Bostedt, Andre Al Haddad, Thomas Roland Barillot

X-ray photoelectron spectroscopy (XPS) measures the binding energy of core-level electrons, which are well-localised to specific atomic sites in a molecular system, providing valuable information on the local chemical environment. The technique relies on m ...

IOP Publishing2021

In-line electronic and structural characterization of reactively sputtered Cu-Co-Mn black spinel oxides

Andreas Schueler, Anna Krammer, Maxime Lagier

Cu-Co-Mn spinel oxide thin films are deposited by reactive magnetron sputtering. The x-ray diffraction (XRD) spectrum suggests a nanocrystalline spinel film when sputtered at approximate to 465 degrees C. In-line scanning tunneling microscopy confirms nano ...

A V S AMER INST PHYSICS2021

A Correlation-Based Electromagnetic Time Reversal Technique to Locate Indoor Transient Radiation Sources

Farhad Rachidi-Haeri, Marcos Rubinstein, Zhaoyang Wang, Qi Li

To overcome the multipath interference in locating transient electromagnetic (EM) radiation sources in an indoor environment, we propose a criterion that calculates the correlation between back-propagated signals from observation points, to be used in EM t ...

Institute of Electrical and Electronics Engineers2021

A miniaturized selective laser melting device for operando X-ray diffraction studies

Steven Van Petegem, Helena Van Swygenhoven, Nicola Casati, Samy Hocine

We report on the development of a miniaturized device for operando X-ray diffraction during laser 3D printing. The printing chamber has a size of only 130 x 135 x 34 mm(3) and is optimized to be installed at synchrotron beamlines. We describe the design co ...

ELSEVIER2020

Operando X-ray diffraction during laser 3D printing

Steven Van Petegem, Helena Van Swygenhoven, Nicola Casati, Samy Hocine

Laser based additive manufacturing allows to build a designed shape layer-by-layer, offering versatility and flexibility to many metallurgical sectors. The fast cooling rates and repeated heat cycles depending on the laser and scanning parameters are not e ...

2020