Concept

Forging

Related publications (25)

Evaluation of Interface and Residual Strain of NiTi Layer Deposited on NiTiX Substrate by Laser Powder Bed Fusion

Elyas Ghafoori, Christian Leinenbach, Irene Ferretto

This study investigates the microstructure and properties of functionally graded NiTi alloy bilayers. The NiTi layer is printed by laser powder bed fusion on a NiTiX (where X is Hf or Cu) substrate prepared by vacuum arc remelting. Specimens produced with ...

Wiley-V C H Verlag Gmbh2024

Laser powder bed fusion of Fe-based shape memory alloys for novel structural metamaterials and "smart" structures

Irene Ferretto

Laser powder bed fusion (LPBF) is a powder-based additive manufacturing (AM) technique, which shows great potential in the production of complex-shaped parts with unprecedented design freedom. In addition, it allows for an active manipulation of the micros ...

EPFL2023

Proposed residual stress model for hot‐rolled wide flange steel cross sections

Dimitrios Lignos, Albano António De Abreu E Presa De Castro E Sousa, Andronikos Skiadopoulos

Residual stresses in hot-rolled wide flange steel cross sections may lead to premature yielding, accelerated corrosion and brittle fracture of steel members. The above phenomena lead to a loss of a steel member's stiffness and resistance under mechanical l ...

Ernst & Sohn2023

Experimental investigation of dowel action using advanced measurement techniques

Aurelio Muttoni, Marko Pejatovic

Existing shear-cracked structures need to be reliably verified in order to avoid redundant interventions. Code provisions often raise shear safety and/or fatigue life concerns of the reinforcement subjected to stress concentrations due to cyclic dowel acti ...

2022

Giant hardening response in AlMgZn(Cu) alloys

William Curtin, Daniel John Gilles Marchand

This study presents a thermomechanical processing concept which is capable of exploiting the full industrial application potential of recently introduced AlMgZn(Cu) alloys. The beneficial linkage of alloy design and processing allows not only to satisfy th ...

PERGAMON-ELSEVIER SCIENCE LTD2021

First observation of spalling in tantalum at high temperatures induced by high energy proton beam impacts

Philippe Spätig, Elvis Fornasiere

Spalling in tantalum has been observed in an experiment aiming at testing an antiproton production target prototype at CERN’s HiRadMat Facility. The experiment consisted in impacting 47 intense and high-energy proton beams onto a target equipped with ten c ...

2020

Mechanical properties of replicated cellular Zn and Zn1.5Mg in uniaxial compression

Andreas Mortensen, Ludger Weber

We present here a study of the mechanical behavior of cellular Zn and Zn1.5Mg with densities between 11.9 and 24.5%, produced by replication processing using NaCl as a spaceholder. Cellular Zn and Zn1.5Mg deform homogeneously during quasi-static compressio ...

ELSEVIER SCIENCE INC2019

Ductility reduction factor formulations for seismic design of RC wall and frame structures

Katrin Beyer, Matteo Zerbin

Seismic design of standard structures is typically founded on a force-based design approach. Over the years this approach has proven robust and easily applicable by design engineers and - in combination with capacity design principles - it provides a good ...

2019

Simulating Local Buckling-Induced Softening in Steel Members Using an Equivalent Nonlocal Material Model in Displacement-Based Fiber Elements

Dimitrios Lignos

Fiber-based elements are commonly used to simulate steel beam-columns because of their ability to capture P-M interactions and spread of plasticity. However, when mechanisms such as local buckling result in effective softening at the fiber scale, conventio ...

2018

Controlling grain structure and texture in Al-Mn from the competition between precipitation and recrystallization

Roland Logé, Ke Huang

The recrystallization behaviour of Al-Mn alloys (AA3xxx series alloys) is affected by randomly distributed dispersoids present before annealing, by dispersoids precipitated at grain/subgrain boundaries before the onset of recrystallization, and by disperso ...

Elsevier2017

Recrystallization behavior of multi-directionally forged over-aged and solution treated Al-Cu-Mg alloy during non-isothermal annealing

Roland Logé

The recrystallization behavior of an Al-Cu-Mg alloy is investigated in multi-directionally forged over-aged and solution treated alloys, during non-isothermal annealing. Deformation and non-isothermal annealing are performed with a Gleeble 3800 thermo-mech ...

Elsevier Sci Ltd2017

The surprising influence of continuous alternating electric current on recrystallization behaviour of a cold-rolled Aluminium alloy

Roland Logé, Cyril Cayron, Ke Huang

Pronounced acceleration of recrystallization in cold worked metals is generally observed during annealing with additional high density electric current pulses. In this work, continuous alternating current of low density was applied to heat cold-rolled samp ...

Elsevier2017

On the sluggish recrystallization of a cold-rolled Al–Mn–Fe–Si alloy

Roland Logé, Ke Huang

Annealing of supersaturated AA3xxx alloys at low temperatures usually results in sluggish recrystallization kinetics. This is due to the joint effect of the following factors: low nucleation rate, reduced grain boundary mobility, and large amount of fine p ...

Springer Verlag2016

Numerical Simulation of Solidification, Homogenization, and Precipitation in an Industrial Ni-Based Superalloy

Alain Jacot, Charles-André Gandin, Luc Rougier

A comprehensive simulation approach integrating solidification, homogenization, and precipitation during aging has been used to predict the formation of gamma/gamma' microstructures in the AM1 nickel-based superalloy. The particle size distribution of intr ...

Springer2016

Investigation of microstructure and mechanical properties of W-Y and W-Y2O3 materials fabricated by powder metallurgy method

Nadine Baluc, Lyubomira Veleva

W-2Y, W-1Y(2)O(3) and W-2Y(2)O(3) materials have been fabricated using two different powder metallurgy methods. While W-2Y and W-1Y(2)O(3) have been fabricated using mechanical alloying and hot isostatic pressing (Hipping), W-2Y(2)O(3) has been fabricated ...

Elsevier Sci Ltd2015

Factors affecting the strength of P{011}〈566〉-texture after annealing of a cold-rolled Al–Mn–Fe–Si alloy

Ke Huang

Elongated coarse P{011}-oriented grains are frequently observed after annealing of cold-rolled Al–Mn alloys with a highly supersaturated solid solution level. In this study, important factors affecting the strength of the P-texture component after ann ...

Springer2015

Effect of heterogeneously distributed pre-existing dispersoids on the recrystallization behavior of a cold-rolled Al–Mn–Fe–Si alloy

Ke Huang

It is well known that strong concurrent precipitation, mainly located along grain/subgrain boundaries, results in a coarse and elongated grain structure, and unusual sharp P {011} and/or M {113} texture components during annealing of supersatur ...

Elsevier2015

Early cluster formation during rapid cooling of an Al-Cu-Mg alloy: In situ small-angle X-ray scattering

Jean-Marie Drezet, Helena Van Swygenhoven, Patrick Schloth

The formation of Cu-Mg clusters in an Al-Cu-Mg aluminum alloy is observed by small-angle X-ray scattering during cooling. Cooling rates are choosen to mimic the different conditions obtained at the surface and in the center of large forgings. Clusters of 0 ...

Elsevier2015

The effect of heating rate on the softening behaviour of a deformed Al–Mn alloy with strong and weak concurrent precipitation

Ke Huang

The interaction between recrystallization and concurrent precipitation is strongly dependent on the heating rate during annealing. In this study, the effects of heating rate on the grain structure, recrystallization texture and resulting mechanical propert ...

Elsevier Science Inc2015

Quench-Induced Stresses in AA2618 Forgings for Impellers: A Multiphysics and Multiscale Problem

Jean-Marie Drezet, Nicolas Paul Henry Chobaut

In the fabrication of heat-treatable aluminum parts such as AA2618 compressor impellers for turbochargers, solutionizing and quenching are key steps to obtain the required mechanical characteristics. Fast quenching is necessary to avoid coarse precipitatio ...

Springer2015