Edoardo CharbonEdoardo Charbon (SM’00 F’17) received the Elektrotechnik Diploma from ETH Zurich, the M.S. from the University of California at San Diego, and the Ph.D. from the University of California at Berkeley in 1988, 1991, and 1995, respectively, all in electrical engineering and EECS. He has consulted with numerous organizations, including Bosch, X-Fab, Texas Instruments, Maxim, Sony, Agilent, and the Carlyle Group. He was with Cadence Design Systems from 1995 to 2000, where he was the architect of the company's initiative on information hiding for intellectual property protection. In 2000, he joined Canesta Inc., as the Chief Architect, where he led the development of wireless 3-D CMOS image sensors. Since 2002 he has been a member of the faculty of EPFL, where is a full professor since 2015. From 2008 to 2016 he was full professor and chair at the Delft University of Technology, where he spearheaded the university's effort on cryogenic electronics for quantum computing as part of QuTech. He has been the driving force behind the creation of deep-submicron CMOS SPAD technology, which is mass-produced since 2015 and is present in smartphones, telemeters, proximity sensors, and medical diagnostics tools. His interests span from 3-D vision, LiDAR, FLIM, FCS, NIROT to super-resolution microscopy, time-resolved Raman spectroscopy, and cryo-CMOS circuits and systems for quantum computing. He has authored or co-authored over 400 papers and two books, and he holds 23 patents. Dr. Charbon is a distinguished visiting scholar of the W. M. Keck Institute for Space at Caltech, a fellow of the Kavli Institute of Nanoscience Delft, a distinguished lecturer of the IEEE Photonics Society, and a fellow of the IEEE.
Jean-Marie Drezet1992-1996: PhD work at Laboratoire de Métallurgie Physique under the supervision of Prof. Michel Rappaz (cf : http://library.epfl.ch/theses/?display=detail&nr=1509) 1997-2000: EMPACT project (European Modelling Programme for Aluminium Casting Technologies) 2001-2004: VIRCAST project (European Virtual Casting) 2005-2006: Study of the sawing process of rolling sheet al. ingots (Alcan Fonds) 2005-2006: WelAIR project (Welding of Airframes, EADS) 2005-2008: study of the electron beam welding of Cu-Cr-Zr alloys (CEA, France) 2006-2008: study of the laser beam welding of Al-Li alloys (EADS, France) 2008-2011: co-supervision with Prof. A. Nussbaumer of the PhD work of C. Acevedo on the influence of residual stresses on the fatigue design of tubular welded joints, http://library.epfl.ch/theses/?nr=5056 2007-2010: co-supervision with Prof. J.-F. Molinari of the PhD work of K. Shahim on the Normal Pressure Hydrocephalus (S. Momjian, HU-Genève et R. Sinkus, ESPCI-Paris), http://library.epfl.ch/theses/?nr=5191 2008-2012: co-supervision with Prof. M. Rappaz of the PhD work of M. Sistaninia on the simulation of solidification cracking using granular models (CCMX-MERU project) 2010-2014: supervision with Prof. M. Rappaz of the PhD work of N. Chobaut on the modelling of stresses during quenching of thick heat treatable aluminium parts (CCMX-MERU project) 2011-2015: supervision with Prof. H. Van Swygenhoven-Moens of the PhD work of P. Schloth on precipitation during quenching of thick heat treatable aluminium parts (CCMX-MERU project) Thomas La GrangeExpertise
Electron Microscopy, Aberration Correct Scanning Transmission Electron Microscopy, Electron Diffraction, Ultrafast Transmission Electron Microscopy, Electron Energy Loss Spectroscopy, Energy Dispersive Spectroscopy, Materials Science, High-speed deformation, Dislocation Dynamics, Skyrmionics, Martensitic Phase Transformation Theory, Solidification
Expertise
Electron Microscopy, Aberration Correct Scanning Transmission Electron Microscopy, Electron Diffraction, Ultrafast Transmission Electron Micro
Iva Tkalcec VâjuTeaching & PhD Past EPFL PhD Students as codirector Lucas Degeneve Courses Physics lab (metrology) PHYS-117 This course is a practical introduction to classical measurement techniques in a physics laboratory. It aims at familiarising the students with data acquisition, sensors, signal processing, vacuum and cryogenics. Physics lab IIIa PHYS-319 The students observe a number of physical phenomena and their technological applications. The course aims at acquiring knowledge abou
Ghassan ShahinExpertise
I am a geomechanics researcher with interests in the mechanical behavior of the Earth's materials at conditions pertaining to the shallow Earth and upper mantle. In my studies, I employ laboratory geomechanics backed by x-ray methods, advanced constitutive modeling, and material theories to study failure patterns across scales spanning from the grain-scale up to the field-scale.
Expertise
I am a geomechanics researcher with interests in the mechanical behavior of the Earth's materials at condition
Dragan DamjanovicDragan Damjanovic received BSc diploma in Physics from the Faculty of Natural Sciences and Mathematics, University of Sarajevo, in 1980, and PhD in Ceramics Science from the Department of Materials Science and Engineering, College of Earth and Mineral Sciences, the Pennsylvania State University (PSU) in 1987. From 1988 to 1991 he was a research associate in the Materials Research Laboratory at the PSU. He joined the Ceramics Laboratory, Department of Materials Science and Engineering, Ecole polytechnique fédérale de Lausanne in 1991. He is currently a "professeur titulaire", heads the Group for Ferroelectrics and Functional Oxides at the Institute of Materials and teaches undergraduate and graduate courses on structure and electrical properties of materials. The research activities include fundamental and applied investigations of piezoelectric, ferroelectric and dielectric properties of a broad class of materials.
Stefano MischlerStefano Mischler obtained the diploma in materials science in 1983 at the Swiss Federal Institute of Technology ETHZ in Zurich. He accomplished his PhD thesis in the field of surface analysis and corrosion at the Materials department of the Swiss Federal Institute of Technology EPFL in Lausanne in 1988. In the years 1989-1990 he held a postdoctoral position at the United Kingdom Atomic Energy Establishment in Harwell (Oxfordshire) where he developed novel quantification procedures for Auger Electron Spectroscopy and high lateral resolution surface analytical methods for fiber reinforced ceramics. In 1991 he joined the newly created Tribology group at the Laboratory for Metallurgical Chemistry of the EPFL where he developed research activities in the field of wear-corrosion interactions (tribocorrosion) and of tribological coatings. He is currently head of the tribology group and is developing a reserach and training activity devoted to modern aspects of tribology and surface science and technology, including surface chemical effects in tribology, biotribology and biocorrosion, tribology in microfabrication processes and wear protection methods. In 2006 he spent a sabbatical leave of 3 months at the Tokyo Medical and Dental University, Institute of Biomaterials.
